'Timeout writing data to COM5' and 'Rs232 SerialPortError' after erase_flash on ESP32 S2 Mini #85

lchmagKekse · 2025-03-22T17:18:57Z

lchmagKekse
Mar 22, 2025

I’m having some problems with my ESP32-S2 Mini.

The LEDs lit up and were working fine before. However, I had configured the second segment start index incorrectly, so I wanted to fix that. When re-flashing the new firmware to the ESP, I ran erase_flash for the first time, followed by flashing the factory firmware.

After that, it stopped working.

I've set up the wiring exactly the same way as shown in the segmentation example: (https://user-images.githubusercontent.com/85223482/222923979-f344349a-1f8b-4195-94ca-51721923359e.png)

These are the two error logs i get:

2025-03-22T17:58:57.562Z [LEDDEVICE0_ADALIGHT] Device 'adalight' is disabled due to an error: 'Timeout writing data to COM5'

2025-03-22T18:02:56.826Z [LEDDEVICE0_ADALIGHT] Device 'adalight' is disabled due to an error: 'Rs232 SerialPortError: Das Ger�t erkennt den Befehl nicht.'

The changes i made to platformio.ini

[env:s2_mini_SK6812_RGBW_COLD]
build_flags = -DNEOPIXEL_RGBW -DCOLD_WHITE -DDATA_PIN=16 -DSECOND_SEGMENT_DATA_PIN=18 -DSECOND_SEGMENT_START_INDEX=169 -DSECOND_SEGMENT_REVERSED ${env.build_flags}
custom_prog_version = esp32_s2_mini_SK6812_RGBW_COLD

How im flashing the esp:

C:\repos\HyperSerialESP32\.pio\build>python -m esptool erase_flash
esptool.py v4.8.1
Found 1 serial ports
Serial port COM6
Connecting...
Detecting chip type... Unsupported detection protocol, switching and trying again...
Detecting chip type... ESP32-S2
Chip is ESP32-S2FNR2 (revision v0.0)
Features: WiFi, Embedded Flash 4MB, Embedded PSRAM 2MB, ADC and temperature sensor calibration in BLK2 of efuse V2
Crystal is 40MHz
MAC: 70:04:1d:fe:e4:2a
Uploading stub...
Running stub...
Stub running...
Erasing flash (this may take a while)...
Chip erase completed successfully in 16.7s
Error: ESP32-S2FNR2 (revision v0.0) chip was placed into download mode using GPIO0.
esptool.py can not exit the download mode over USB. To run the app, reset the chip manually.
To suppress this note, set --after option to 'no_reset'.

C:\repos\HyperSerialESP32\.pio\build>python -m esptool write_flash 0x0 firmware_esp32_s2_mini_SK6812_RGBW_COLD.factory.bin
esptool.py v4.8.1
Found 1 serial ports
Serial port COM6
Connecting...
Detecting chip type... Unsupported detection protocol, switching and trying again...
Detecting chip type... ESP32-S2
Chip is ESP32-S2FNR2 (revision v0.0)
Features: WiFi, Embedded Flash 4MB, Embedded PSRAM 2MB, ADC and temperature sensor calibration in BLK2 of efuse V2
Crystal is 40MHz
MAC: 70:04:1d:fe:e4:2a
Uploading stub...
Running stub...
Stub running...
Configuring flash size...
Flash will be erased from 0x00000000 to 0x0004efff...
Compressed 323488 bytes to 159392...
Wrote 323488 bytes (159392 compressed) at 0x00000000 in 4.1 seconds (effective 632.2 kbit/s)...
Hash of data verified.

Leaving...
Error: ESP32-S2FNR2 (revision v0.0) chip was placed into download mode using GPIO0.
esptool.py can not exit the download mode over USB. To run the app, reset the chip manually.
To suppress this note, set --after option to 'no_reset'.

Here is the full log output of HyperHDR:

2025-03-22T17:29:16.305Z [DX11_SYSTEM:\\.\DISPLAY1|A] (Grabber.cpp:497) setDeviceVideoStandard preparing to restart video grabber. Old: '' new: '\\.\DISPLAY1|AMD Radeon(TM) Graphics'
2025-03-22T17:29:16.305Z [DX11_SYSTEM:\\.\DISPLAY1|A] Delayed restart of the grabber due to change of selected device
2025-03-22T17:29:16.305Z [INSTANCE_CFG0] Settings database initialized
2025-03-22T17:29:16.305Z [COMPONENTCTRL0] (ComponentController.cpp:27) ComponentController is initialized. Components are ENABLED
2025-03-22T17:29:16.305Z [MUXER0] (Muxer.cpp:54) Muxer initialized
2025-03-22T17:29:16.305Z [BLACKBORDER] Set mode to: default
2025-03-22T17:29:16.305Z [IMAGETOLED_MNG0] (ImageToLedManager.cpp:192) Set LED mapping type to advanced
2025-03-22T17:29:16.305Z [IMAGETOLED_MNG0] (ImageToLedManager.cpp:176) setSparseProcessing to 0
2025-03-22T17:29:16.305Z [IMAGETOLED_MNG0] (ImageToLedManager.cpp:103) ImageToLedManager initialized
2025-03-22T17:29:16.305Z [COLORSPACE_CALIBRATION0] classicMode: no, gammas:[1.50, 1.50, 1.50], saturation: 1.00, luminance: 1.00, backLight: [enabled, threshold: 1, colored: yes]
2025-03-22T17:29:16.305Z [LED_CALIBRATION0] (LedCalibration.cpp:101) Calibration config '0' for LED segment: [0, 338]
2025-03-22T17:29:16.305Z [HYPERHDR0] Led strip RGB order is: rgb
2025-03-22T17:29:16.305Z [SMOOTHING0] High resolution clock is steady (good)
2025-03-22T17:29:16.305Z [SMOOTHING0] Clearing queued colors before: enabling
2025-03-22T17:29:16.305Z [SMOOTHING0] Smoothing queue is cleared
2025-03-22T17:29:16.305Z [COMPONENTCTRL0] Smoothing: enabled
2025-03-22T17:29:16.305Z [SMOOTHING0] Creating config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
2025-03-22T17:29:16.305Z [SMOOTHING0] Clearing queued colors before: enabling. Smoothing configuration changed: restarting timer.
2025-03-22T17:29:16.305Z [SMOOTHING0] Smoothing queue is cleared
2025-03-22T17:29:16.305Z [SMOOTHING0] Selecting config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
2025-03-22T17:29:16.305Z [SMOOTHING0] Selecting config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] Start LedDevice 'adalight'.
2025-03-22T17:29:16.305Z [HYPER_MANAGER] HyperHDR instance 'First LED instance' has been started
2025-03-22T17:29:16.305Z [HYPERHDR0] The instance is running
2025-03-22T17:29:16.305Z [MUXER0] Register new input 'System/VIDEOGRABBER' with priority 240 as inactive
2025-03-22T17:29:16.305Z [COMPONENTCTRL0] Video capture device: enabled
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:336) deviceConfig: [{"awa_mode":true,"colorOrder":"rgb","currentLedCount":339,"espHandshake":true,"forceSerialDetection":false,"maxRetry":0,"output":"COM5","rate":2000000,"refreshTime":20,"smoothingRefreshTime":20,"type":"adalight","white_channel_calibration":false}]
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] Ignoring user LED refresh rate. Forcing smoothing refresh rate = 50.00 Hz
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:422) Refresh rate = 50.00 Hz
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:372) Device is not ready to start a timer
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:432) Refresh interval updated to 20ms
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:50) DeviceType   : adalight
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:51) LedCount     : 339
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:52) RefreshTime  : 20
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:67) Device name   : COM5
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:68) Auto selection: 0
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:69) Baud rate     : 2000000
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:70) ESP handshake : ON
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:71) Force ESP/Pico Detection : OFF
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:72) Delayed open  : 0
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:73) Retry limit   : 0
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] The refresh timer is enabled ('Refresh time' > 0) and may limit the performance of the LED driver. Ignore this error if you set it on purpose for some reason (but you almost never need it).
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] (DriverSerialAdalight.cpp:78) Adalight driver with activated high speeed & data integration check AWA protocol
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] (DriverSerialAdalight.cpp:88) Adalight header for 339 leds: Awa 0x01 0x52 0x06
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:246) Enable the device
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] Opening UART: COM5
2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:209) _serialPort.open(QIODevice::ReadWrite): COM5, Baud rate [2000000]bps
2025-03-22T17:29:16.321Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:214) portName:          COM5
2025-03-22T17:29:16.321Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:215) systemLocation:    \\.\COM5
2025-03-22T17:29:16.321Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:216) description:       Serielles USB-Ger�t
2025-03-22T17:29:16.321Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:217) manufacturer:      Microsoft
2025-03-22T17:29:16.321Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:218) productIdentifier: 0x80c2
2025-03-22T17:29:16.321Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:219) vendorIdentifier:  0x303a
2025-03-22T17:29:16.321Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:220) serialNumber:      0
2025-03-22T17:29:16.351Z [LEDDEVICE0_ADALIGHT] Detected ESP32-S2 lolin mini type board. HyperHDR skips the reset. State: 0, 0
2025-03-22T17:29:16.431Z [LEDDEVICE0_ADALIGHT] ESP sent: 'HyperHDR frames: 0 (FPS), receiv.: 0, good: 0, incompl.: 0, mem1: 4532, mem2: 3768, heap: 189708'
2025-03-22T17:29:16.431Z [LEDDEVICE0_ADALIGHT] ESP sent: 'RGBW => Gain: 255/255, red: 160, green: 160, blue: 160'
2025-03-22T17:29:16.431Z [LEDDEVICE0_ADALIGHT] DETECTED DEVICE USING HyperSerialEsp8266/HyperSerialESP32/HyperSerialPico FIRMWARE (Welcome! Awa driver 9.) at 2 msec
2025-03-22T17:29:16.431Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:63) Switch on
2025-03-22T17:29:16.431Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:139) Power On
2025-03-22T17:29:16.431Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:366) Starting timer with interval = 20ms
2025-03-22T17:29:16.434Z [COMPONENTCTRL0] LED device: enabled
2025-03-22T17:29:16.434Z [SMOOTHING0] Using alternative smoothing input (0)
2025-03-22T17:29:16.434Z [EFFECTENGINE0] Run effect "Rainbow swirl fast" on channel 0
2025-03-22T17:29:16.434Z [EFFECTENGINE0] (EffectEngine.cpp:92) Start the effect: name [Rainbow swirl fast]
2025-03-22T17:29:16.434Z [MUXER0] Register new input 'System/EFFECT' with priority 0 as inactive
2025-03-22T17:29:16.434Z [HYPERHDR0] Boot effect: animation set to 'Rainbow swirl fast' [started]
2025-03-22T17:29:16.434Z [EFFECT0(Rainbo...)] Begin playing the effect with priority: 0
2025-03-22T17:29:16.434Z [MUXER0] Priority 0 is now active
2025-03-22T17:29:16.434Z [MUXER0] Set visible priority to 0
2025-03-22T17:29:16.434Z [SMOOTHING0] Clearing queued colors before: enabling. Smoothing configuration changed: restarting timer.
2025-03-22T17:29:16.434Z [SMOOTHING0] Smoothing queue is cleared
2025-03-22T17:29:16.434Z [SMOOTHING0] Selecting config (1) => type: Linear, pause: false, settlingTime: 200ms, interval: 40ms (25Hz), antiFlickTres: 0, antiFlickStep: 0, antiFlickTime: 0
2025-03-22T17:29:16.434Z [SMOOTHING0] Using linear smoothing input (1)
2025-03-22T17:29:16.434Z [HYPERHDR0] New priority[0], previous [255]
2025-03-22T17:29:16.434Z [HYPERHDR0] New source available -> switch LED-Device on
2025-03-22T17:29:16.434Z [SMOOTHING0] Clearing queued colors before: enabling
2025-03-22T17:29:16.434Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:380) Stopping refresh timer
2025-03-22T17:29:16.434Z [SMOOTHING0] Smoothing queue is cleared
2025-03-22T17:29:16.434Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:224) setBackLightEnabled: 0
2025-03-22T17:29:16.434Z [LEDDEVICE0_ADALIGHT] Ignoring user LED refresh rate. Forcing smoothing refresh rate = 25.00 Hz
2025-03-22T17:29:16.434Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:422) Refresh rate = 25.00 Hz
2025-03-22T17:29:16.434Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:366) Starting timer with interval = 40ms
2025-03-22T17:29:16.434Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:432) Refresh interval updated to 40ms
2025-03-22T17:29:16.434Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:447) LED refresh interval adjustment caused by smoothing configuration change to 40ms (proposed: 40ms)
2025-03-22T17:29:16.434Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:246) Enable the device
2025-03-22T17:29:16.434Z [IMAGETOLED_MNG0] Total index number is: 1356 (memory: 1356). User sparse processing is: disabled, image size: 80 x 45, area number: 339
2025-03-22T17:29:16.434Z [SMOOTHING0] Using linear smoothing input (1)
2025-03-22T17:29:16.449Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:465) Device has 'brightness' control => min: 0, max: 100, default: 50
2025-03-22T17:29:16.449Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:472) Device has 'contrast' control => min: 0, max: 100, default: 32
2025-03-22T17:29:16.450Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:479) Device has 'saturation' control => min: 0, max: 20, default: 4
2025-03-22T17:29:16.450Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:486) Device has 'hue' control => min: -180, max: 180, default: 0
2025-03-22T17:29:16.450Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 1280 x 720 @ 30 fps NV12 (nv12)
2025-03-22T17:29:16.450Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 1280 x 720 @ 30 fps MJPG (mjpeg)
2025-03-22T17:29:16.450Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 640 x 480 @ 30 fps NV12 (nv12)
2025-03-22T17:29:16.450Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 640 x 480 @ 30 fps MJPG (mjpeg)
2025-03-22T17:29:16.450Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 640 x 360 @ 30 fps NV12 (nv12)
2025-03-22T17:29:16.450Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 640 x 360 @ 30 fps MJPG (mjpeg)
2025-03-22T17:29:16.450Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 352 x 288 @ 30 fps NV12 (nv12)
2025-03-22T17:29:16.450Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 352 x 288 @ 30 fps MJPG (mjpeg)
2025-03-22T17:29:16.450Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 320 x 240 @ 30 fps NV12 (nv12)
2025-03-22T17:29:16.450Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 320 x 240 @ 30 fps MJPG (mjpeg)
2025-03-22T17:29:16.450Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 176 x 144 @ 30 fps NV12 (nv12)
2025-03-22T17:29:16.450Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 176 x 144 @ 30 fps MJPG (mjpeg)
2025-03-22T17:29:16.452Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 160 x 120 @ 30 fps NV12 (nv12)
2025-03-22T17:29:16.452Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 160 x 120 @ 30 fps MJPG (mjpeg)
2025-03-22T17:29:16.452Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 1280 x 720 @ 10 fps YUY2 (yuyv)
2025-03-22T17:29:16.452Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 640 x 480 @ 30 fps YUY2 (yuyv)
2025-03-22T17:29:16.452Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 640 x 360 @ 30 fps YUY2 (yuyv)
2025-03-22T17:29:16.452Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 352 x 288 @ 30 fps YUY2 (yuyv)
2025-03-22T17:29:16.452Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 320 x 240 @ 30 fps YUY2 (yuyv)
2025-03-22T17:29:16.452Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 176 x 144 @ 30 fps YUY2 (yuyv)
2025-03-22T17:29:16.452Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 160 x 120 @ 30 fps YUY2 (yuyv)
2025-03-22T17:29:16.453Z [MEDIA_FOUNDATION:AUTO] Restarting video grabber is now blocked due to reloading of the configuration
2025-03-22T17:29:16.453Z [MEDIA_FOUNDATION:AUTO] Cropping image: width=0 height=0; crop: left=0 right=0 top=0 bottom=0 
2025-03-22T17:29:16.453Z [Media Foundation:auto] (GrabberWrapper.cpp:180) CEC keycode. Start: 0, stop: 0
2025-03-22T17:29:16.454Z [MEDIA_FOUNDATION:AUTO] (Grabber.cpp:390) setBrightnessContrastSaturationHue nothing changed
2025-03-22T17:29:16.454Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:184) setHdrToneMappingMode to: Disabled
2025-03-22T17:29:16.454Z [AUTOTONEMAPPING] Tone mapping is currently: disabled
2025-03-22T17:29:16.454Z [MEDIA_FOUNDATION:AUTO] (Grabber.cpp:299) setFpsSoftwareDecimation to: 1
2025-03-22T17:29:16.454Z [SIGNAL_OLD] (DetectionManual.cpp:84) Signal detection area set to: 0.250000,0.250000 x 0.750000,0.750000
2025-03-22T17:29:16.454Z [SIGNAL_OLD] (DetectionManual.cpp:74) Signal threshold set to: {12, 12, 12} and frames: 200
2025-03-22T17:29:16.454Z [SIGNAL_AUTO] (DetectionAutomatic.cpp:376) Automatic signal detection -> errorTolerance: 9, modelTolerance: 90, sleepTime: 5000, wakeTime: 1000
2025-03-22T17:29:16.454Z [MEDIA_FOUNDATION:AUTO] (Grabber.cpp:497) setDeviceVideoStandard preparing to restart video grabber. Old: '' new: 'auto'
2025-03-22T17:29:16.454Z [MEDIA_FOUNDATION:AUTO] Delayed restart of the grabber due to change of selected device
2025-03-22T17:29:16.454Z [MEDIA_FOUNDATION:AUTO] (Grabber.cpp:317) Force encoding to: NO_CHANGE (old: NO_CHANGE)
2025-03-22T17:29:16.454Z [MEDIA_FOUNDATION:AUTO] setQFrameDecimation is now: disabled
2025-03-22T17:29:16.454Z [AUTOTONEMAPPING] Enabled: no, time to enable: 30s, time to disable: 500ms, thresholds: { 180, 175, 160}
2025-03-22T17:29:16.454Z [MEDIA_FOUNDATION:AUTO] Multithreading for MEDIA_FOUNDATION is enabled. Available thread's count 4
2025-03-22T17:29:16.454Z [MEDIA_FOUNDATION:AUTO] Starting to enumerate video capture devices
2025-03-22T17:29:16.454Z [FLATBUFSERVER] Tone mapping: 0
2025-03-22T17:29:16.455Z [WEBSERVER] Initialize Webserver
2025-03-22T17:29:16.455Z [FLATBUFSERVER] Started on port 19400
2025-03-22T17:29:16.455Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:426) Detected 1 devices
2025-03-22T17:29:16.455Z [MEDIA_FOUNDATION:AUTO] Found capture device: Chicony USB2.0 Camera
2025-03-22T17:29:16.455Z [FLATBUFSERVER] Started local domain socket server: 'hyperhdr-domain'
2025-03-22T17:29:16.455Z [FLATBUFSERVER] Tone mapping: 0
2025-03-22T17:29:16.455Z [FLATBUFSERVER] NV12 quarter of frame mode: 0
2025-03-22T17:29:16.462Z [NETFORWARDER] Forwarder has changed state to disabled
2025-03-22T17:29:16.472Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:465) Device has 'brightness' control => min: 0, max: 100, default: 50
2025-03-22T17:29:16.472Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:472) Device has 'contrast' control => min: 0, max: 100, default: 32
2025-03-22T17:29:16.472Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:479) Device has 'saturation' control => min: 0, max: 20, default: 4
2025-03-22T17:29:16.473Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:486) Device has 'hue' control => min: -180, max: 180, default: 0
2025-03-22T17:29:16.475Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:261) Forcing auto discovery device
2025-03-22T17:29:16.475Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:266) Auto discovery set to Chicony USB2.0 Camera
2025-03-22T17:29:16.475Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:282) Searching for Chicony USB2.0 Camera 0 x 0 @ 0 fps (NO_CHANGE)
2025-03-22T17:29:16.475Z [MEDIA_FOUNDATION:AUTO] Forcing best guess
2025-03-22T17:29:16.475Z [MEDIA_FOUNDATION:AUTO] *************************************************************************************************
2025-03-22T17:29:16.475Z [MEDIA_FOUNDATION:AUTO] Starting MF grabber. Selected: 'Chicony USB2.0 Camera' 640 x 480 @ 30 fps yuyv
2025-03-22T17:29:16.475Z [MEDIA_FOUNDATION:AUTO] *************************************************************************************************
2025-03-22T17:29:16.475Z [MEDIA_FOUNDATION:AUTO] Init Chicony USB2.0 Camera, 640 x 480 @ 30 fps (YUY2) => \\?\usb#vid_04f2&pid_b729&mi_00#7&191d7230&0&0000#{e5323777-f976-4f5b-9b55-b94699c46e44}\global
2025-03-22T17:29:16.490Z [MEDIA_FOUNDATION:AUTO] Device opened successfully
2025-03-22T17:29:16.491Z [MEDIA_FOUNDATION:AUTO] Brightness set to: 50 (default)
2025-03-22T17:29:16.491Z [MEDIA_FOUNDATION:AUTO] Contrast set to: 32 (default)
2025-03-22T17:29:16.492Z [MEDIA_FOUNDATION:AUTO] Saturation set to: 4 (default)
2025-03-22T17:29:16.492Z [MEDIA_FOUNDATION:AUTO] Hue set to: 0 (default)
2025-03-22T17:29:16.493Z [MEDIA_FOUNDATION:AUTO] ******************** SUCCESFULLY SET CAPTURE PARAMETERS: 640 480 yuyv ********************
2025-03-22T17:29:16.500Z [MEDIA_FOUNDATION:AUTO] (LutLoader.cpp:73) LUT file found: C:/Users/alexb/.hyperhdr/lut_lin_tables.3d (uncompressed)
2025-03-22T17:29:16.500Z [MEDIA_FOUNDATION:AUTO] (LutLoader.cpp:89) Index 2 for YUV
2025-03-22T17:29:16.515Z [SMOOTHING0] Using linear smoothing procedure (1)
2025-03-22T17:29:16.528Z [MEDIA_FOUNDATION:AUTO] Found and loaded LUT: 'C:/Users/alexb/.hyperhdr/lut_lin_tables.3d'
2025-03-22T17:29:16.529Z [MEDIA_FOUNDATION:AUTO] Started
2025-03-22T17:29:16.698Z [WEBSERVER] Apply Webserver settings
2025-03-22T17:29:16.698Z [WEBSERVER] Set document root to: :/www
2025-03-22T17:29:16.698Z [WEBSERVER] Started: 'HyperHDR WebServer (HTTP)' on port: 8090
2025-03-22T17:29:16.699Z [SSDP] (SSDPHandler.cpp:93) The local address is empty
2025-03-22T17:29:16.699Z [WEBSERVER] Initialize Webserver
2025-03-22T17:29:16.699Z [WEBSERVER] Apply Webserver settings
2025-03-22T17:29:16.699Z [WEBSERVER] Set document root to: :/www
2025-03-22T17:29:16.706Z [MEDIA_FOUNDATION:AUTO] Received empty image frame: Warning: receive empty sample
2025-03-22T17:29:16.709Z [WEBSERVER] Setup SSL certificate
2025-03-22T17:29:16.710Z [WEBSERVER] Setup private SSL key
2025-03-22T17:29:16.710Z [WEBSERVER] Started: 'HyperHDR WebServer (HTTPS)' on port: 8092
2025-03-22T17:29:16.710Z [SSDP] (SSDPHandler.cpp:42) SSDPHandler is initializing
2025-03-22T17:29:16.712Z [SSDP] (SSDPHandler.cpp:183) The local address is: 192.168.178.31
2025-03-22T17:29:16.712Z [SSDP] (SSDPServer.cpp:94) Initialize the SSDP server
2025-03-22T17:29:16.713Z [SSDP] Starting the SSDP server
2025-03-22T17:29:16.934Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:992) Worker's thread count  = 4
2025-03-22T17:29:16.936Z [MUXER0] Priority 240 is now active
2025-03-22T17:29:18.202Z [NET_DISCOVERY] Found ESP32-S2 at COM5:-1 (Serielles USB-Ger�t)
2025-03-22T17:29:18.201Z [SERVICE_mDNS] Starting the network discovery thread
2025-03-22T17:29:18.210Z [NET_DISCOVERY] Found HyperHDR at 192.168.178.24:8090 (LGwebOSTV.local)
2025-03-22T17:29:19.437Z [EFFECT0(Rainbo...)] The effect quits with priority: 0
2025-03-22T17:29:19.437Z [MUXER0] Removed source priority 0
2025-03-22T17:29:19.437Z [MUXER0] Set visible priority to 240
2025-03-22T17:29:19.437Z [SMOOTHING0] Clearing queued colors before: enabling. Smoothing configuration changed: restarting timer.
2025-03-22T17:29:19.437Z [SMOOTHING0] Smoothing queue is cleared
2025-03-22T17:29:19.437Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:380) Stopping refresh timer
2025-03-22T17:29:19.437Z [SMOOTHING0] Selecting config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
2025-03-22T17:29:19.437Z [SMOOTHING0] Using alternative smoothing input (0)
2025-03-22T17:29:19.437Z [HYPERHDR0] New priority[240], previous [0]
2025-03-22T17:29:19.437Z [LEDDEVICE0_ADALIGHT] Ignoring user LED refresh rate. Forcing smoothing refresh rate = 50.00 Hz
2025-03-22T17:29:19.437Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:224) setBackLightEnabled: 1
2025-03-22T17:29:19.437Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:422) Refresh rate = 50.00 Hz
2025-03-22T17:29:19.437Z [EFFECTENGINE0] Effect 'Rainbow swirl fast' has finished.
2025-03-22T17:29:19.437Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:366) Starting timer with interval = 20ms
2025-03-22T17:29:19.438Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:432) Refresh interval updated to 20ms
2025-03-22T17:29:19.438Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:447) LED refresh interval adjustment caused by smoothing configuration change to 20ms (proposed: 20ms)
2025-03-22T17:29:19.438Z [EFFECT0(Rainbo...)] Effect named: 'Rainbow swirl fast' is deleted
2025-03-22T17:29:19.460Z [IMAGETOLED_MNG0] Total index number is: 79360 (memory: 79360). User sparse processing is: disabled, image size: 640 x 480, area number: 339
2025-03-22T17:29:19.478Z [SMOOTHING0] Using alternative smoothing procedure (0)
2025-03-22T17:29:25.724Z [WEBSERVER] Web server resources initialized: C:/Program Files/HyperHDR/bin/../lib/web_resources.rcc
2025-03-22T17:29:25.846Z [WEBSOCKET] (WebSocketClient.cpp:40) New connection from ::1
2025-03-22T17:29:31.215Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":39}]
2025-03-22T17:29:31.217Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"Serielles USB-Gerät (\\\\.\\COM5)","value":"COM5"}],"ledDeviceType":"adalight"}]
2025-03-22T17:29:39.727Z [WEBSOCKET] (WebSocketClient.cpp:189) send close: 1000 
2025-03-22T17:29:39.821Z [WEBSOCKET] (WebSocketClient.cpp:40) New connection from ::1
2025-03-22T17:29:40.081Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":111}]
2025-03-22T17:29:40.082Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"Serielles USB-Gerät (\\\\.\\COM5)","value":"COM5"}],"ledDeviceType":"adalight"}]
2025-03-22T17:29:45.687Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:146) Flush was successful
2025-03-22T17:29:46.190Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:164) Serial port is closed: COM5
2025-03-22T17:29:46.190Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:380) Stopping refresh timer
2025-03-22T17:29:46.190Z [LEDDEVICE0_ADALIGHT] Device 'adalight' is disabled due to an error: 'Rs232 SerialPortError: Das Ger�t erkennt den Befehl nicht.'
2025-03-22T17:29:46.190Z [COMPONENTCTRL0] LED device: disabled
2025-03-22T17:29:51.567Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":708}]
2025-03-22T17:29:51.568Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"Serielles USB-Gerät (\\\\.\\COM5)","value":"COM5"}],"ledDeviceType":"adalight"}]
2025-03-22T17:30:07.077Z [WEBSOCKET] (HyperAPI.cpp:946) log streaming activated for client ::1
2025-03-22T17:31:16.262Z [MEDIA_FOUNDATION:AUTO] Video cache: size: 2, hits: 3588, needed: 1, cleanup: 0, limit: 8
2025-03-22T17:31:16.264Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]
2025-03-22T17:32:16.248Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]
2025-03-22T17:33:16.250Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]
2025-03-22T17:34:16.267Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1805, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1805]
2025-03-22T17:35:16.269Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]
2025-03-22T17:36:16.255Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]
2025-03-22T17:37:16.256Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]
2025-03-22T17:38:16.288Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1805, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]
2025-03-22T17:39:16.243Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1803, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]
2025-03-22T17:40:16.276Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1805, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1805]
2025-03-22T17:41:16.263Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]
2025-03-22T17:42:16.264Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]
2025-03-22T17:43:16.249Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]
2025-03-22T17:44:16.251Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]
2025-03-22T17:45:00.075Z [WEBSOCKET] (WebSocketClient.cpp:189) send close: 1000 
2025-03-22T17:45:00.173Z [WEBSOCKET] (WebSocketClient.cpp:40) New connection from ::1
2025-03-22T17:45:00.302Z [WEBSOCKET] (HyperAPI.cpp:946) log streaming activated for client ::1
2025-03-22T17:45:04.076Z [WEBSOCKET] (WebSocketClient.cpp:189) send close: 1000 
2025-03-22T17:45:04.158Z [WEBSOCKET] (WebSocketClient.cpp:40) New connection from ::1
2025-03-22T17:45:04.280Z [WEBSOCKET] (HyperAPI.cpp:946) log streaming activated for client ::1
2025-03-22T17:45:07.471Z [WEBSOCKET] (HyperAPI.cpp:955) log streaming deactivated for client  ::1
2025-03-22T17:45:07.870Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":925}]
2025-03-22T17:45:07.871Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"Serielles USB-Gerät (\\\\.\\COM5)","value":"COM5"}],"ledDeviceType":"adalight"}]
2025-03-22T17:45:11.058Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":333}]
2025-03-22T17:45:11.059Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"Serielles USB-Gerät (\\\\.\\COM5)","value":"COM5"}],"ledDeviceType":"adalight"}]
2025-03-22T17:45:16.268Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1805, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1805]
2025-03-22T17:45:17.419Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:285) Stop device
2025-03-22T17:45:17.419Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:296) Disable the device
2025-03-22T17:45:17.419Z [LEDDEVICE0_ADALIGHT]  Stopped LedDevice 'adalight'
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] Start LedDevice 'adalight'.
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:336) deviceConfig: [{"awa_mode":true,"colorOrder":"rgb","currentLedCount":339,"espHandshake":false,"forceSerialDetection":false,"hardwareLedCount":null,"maxRetry":0,"output":"COM5","rate":2000000,"refreshTime":20,"smoothingRefreshTime":20,"type":"adalight","white_channel_calibration":false}]
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] Ignoring user LED refresh rate. Forcing smoothing refresh rate = 50.00 Hz
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:422) Refresh rate = 50.00 Hz
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:372) Device is not ready to start a timer
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:432) Refresh interval updated to 20ms
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:50) DeviceType   : adalight
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:51) LedCount     : 339
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:52) RefreshTime  : 20
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:67) Device name   : COM5
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:68) Auto selection: 0
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:69) Baud rate     : 2000000
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:70) ESP handshake : OFF
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:71) Force ESP/Pico Detection : OFF
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:72) Delayed open  : 0
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:73) Retry limit   : 0
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] The refresh timer is enabled ('Refresh time' > 0) and may limit the performance of the LED driver. Ignore this error if you set it on purpose for some reason (but you almost never need it).
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] (DriverSerialAdalight.cpp:78) Adalight driver with activated high speeed & data integration check AWA protocol
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] (DriverSerialAdalight.cpp:88) Adalight header for 339 leds: Awa 0x01 0x52 0x06
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:246) Enable the device
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] Opening UART: COM5
2025-03-22T17:45:17.421Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:209) _serialPort.open(QIODevice::ReadWrite): COM5, Baud rate [2000000]bps
2025-03-22T17:45:17.422Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:214) portName:          COM5
2025-03-22T17:45:17.422Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:215) systemLocation:    \\.\COM5
2025-03-22T17:45:17.422Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:216) description:       Serielles USB-Ger�t
2025-03-22T17:45:17.422Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:217) manufacturer:      Microsoft
2025-03-22T17:45:17.422Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:218) productIdentifier: 0x80c2
2025-03-22T17:45:17.422Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:219) vendorIdentifier:  0x303a
2025-03-22T17:45:17.422Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:220) serialNumber:      0
2025-03-22T17:45:17.447Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:63) Switch on
2025-03-22T17:45:17.447Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:139) Power On
2025-03-22T17:45:17.448Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:366) Starting timer with interval = 20ms
2025-03-22T17:45:17.448Z [COMPONENTCTRL0] LED device: enabled
2025-03-22T17:45:20.345Z [WEBSOCKET] (WebSocketClient.cpp:189) send close: 1000 
2025-03-22T17:45:20.444Z [WEBSOCKET] (WebSocketClient.cpp:40) New connection from ::1
2025-03-22T17:45:20.626Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":194}]
2025-03-22T17:45:20.628Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"Serielles USB-Gerät (\\\\.\\COM5)","value":"COM5"}],"ledDeviceType":"adalight"}]
2025-03-22T17:45:20.779Z [WEBSOCKET] (WebSocketClient.cpp:189) send close: 1000 
2025-03-22T17:45:20.860Z [WEBSOCKET] (WebSocketClient.cpp:40) New connection from ::1
2025-03-22T17:45:21.028Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":613}]
2025-03-22T17:45:21.029Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"Serielles USB-Gerät (\\\\.\\COM5)","value":"COM5"}],"ledDeviceType":"adalight"}]
2025-03-22T17:47:16.315Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804], [LED0: FPS = 5.88, send = 353, processed = 353, dropped = 2646]
2025-03-22T17:48:16.323Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804], [LED0: FPS = 5.88, send = 353, processed = 353, dropped = 2646]
2025-03-22T17:49:16.330Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 2ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.06, processed = 1804], [LED0: FPS = 5.88, send = 353, processed = 353, dropped = 2646]
2025-03-22T17:50:16.338Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 3ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.06, processed = 1803], [LED0: FPS = 5.88, send = 353, processed = 353, dropped = 2646]
2025-03-22T17:51:16.346Z [PERFORMANCE] [USB: FPS = 30.08, decoding = 1ms, frames = 1805, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.08, processed = 1805], [LED0: FPS = 5.88, send = 353, processed = 353, dropped = 2646]
2025-03-22T17:51:35.594Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 0 frames already dropped
2025-03-22T17:51:36.594Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 1 frames already dropped
2025-03-22T17:51:37.595Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 2 frames already dropped
2025-03-22T17:51:38.595Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 3 frames already dropped
2025-03-22T17:51:39.596Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 4 frames already dropped
2025-03-22T17:51:40.596Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 5 frames already dropped
2025-03-22T17:51:40.596Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:146) Flush was successful
2025-03-22T17:51:40.596Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:164) Serial port is closed: COM5
2025-03-22T17:51:40.596Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:380) Stopping refresh timer
2025-03-22T17:51:40.596Z [LEDDEVICE0_ADALIGHT] Device 'adalight' is disabled due to an error: 'Timeout writing data to COM5'
2025-03-22T17:51:40.596Z [COMPONENTCTRL0] LED device: disabled
2025-03-22T17:51:40.596Z [PERFORMANCE] [USB: FPS = 30.08, decoding = 1ms, frames = 1805, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.08, processed = 1805]
2025-03-22T17:52:06.064Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:285) Stop device
2025-03-22T17:52:06.064Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:296) Disable the device
2025-03-22T17:52:06.064Z [LEDDEVICE0_ADALIGHT]  Stopped LedDevice 'adalight'
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] Start LedDevice 'adalight'.
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:336) deviceConfig: [{"awa_mode":true,"colorOrder":"rgb","currentLedCount":339,"espHandshake":false,"forceSerialDetection":false,"hardwareLedCount":null,"maxRetry":0,"output":"COM5","rate":115200,"refreshTime":20,"smoothingRefreshTime":20,"type":"adalight","white_channel_calibration":false}]
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] Ignoring user LED refresh rate. Forcing smoothing refresh rate = 50.00 Hz
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:422) Refresh rate = 50.00 Hz
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:372) Device is not ready to start a timer
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:432) Refresh interval updated to 20ms
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:50) DeviceType   : adalight
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:51) LedCount     : 339
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:52) RefreshTime  : 20
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:67) Device name   : COM5
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:68) Auto selection: 0
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:69) Baud rate     : 115200
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:70) ESP handshake : OFF
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:71) Force ESP/Pico Detection : OFF
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:72) Delayed open  : 0
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:73) Retry limit   : 0
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] The refresh timer is enabled ('Refresh time' > 0) and may limit the performance of the LED driver. Ignore this error if you set it on purpose for some reason (but you almost never need it).
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] (DriverSerialAdalight.cpp:78) Adalight driver with activated high speeed & data integration check AWA protocol
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] (DriverSerialAdalight.cpp:88) Adalight header for 339 leds: Awa 0x01 0x52 0x06
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:246) Enable the device
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] Opening UART: COM5
2025-03-22T17:52:06.065Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:209) _serialPort.open(QIODevice::ReadWrite): COM5, Baud rate [115200]bps
2025-03-22T17:52:06.066Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:214) portName:          COM5
2025-03-22T17:52:06.066Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:215) systemLocation:    \\.\COM5
2025-03-22T17:52:06.066Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:216) description:       Serielles USB-Ger�t
2025-03-22T17:52:06.066Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:217) manufacturer:      Microsoft
2025-03-22T17:52:06.066Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:218) productIdentifier: 0x80c2
2025-03-22T17:52:06.066Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:219) vendorIdentifier:  0x303a
2025-03-22T17:52:06.066Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:220) serialNumber:      0
2025-03-22T17:52:06.092Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:63) Switch on
2025-03-22T17:52:06.092Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:139) Power On
2025-03-22T17:52:06.092Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:366) Starting timer with interval = 20ms
2025-03-22T17:52:06.092Z [COMPONENTCTRL0] LED device: enabled
2025-03-22T17:52:09.020Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":865}]
2025-03-22T17:52:09.022Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"Serielles USB-Gerät (\\\\.\\COM5)","value":"COM5"}],"ledDeviceType":"adalight"}]
2025-03-22T17:52:14.231Z [WEBSOCKET] (WebSocketClient.cpp:189) send close: 1000 
2025-03-22T17:52:14.316Z [WEBSOCKET] (WebSocketClient.cpp:40) New connection from ::1
2025-03-22T17:52:14.491Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":48}]
2025-03-22T17:52:14.493Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"Serielles USB-Gerät (\\\\.\\COM5)","value":"COM5"}],"ledDeviceType":"adalight"}]
2025-03-22T17:53:16.340Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1805, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1805], [LED0: FPS = 5.88, send = 353, processed = 353, dropped = 2646]
2025-03-22T17:54:16.348Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804], [LED0: FPS = 5.88, send = 353, processed = 353, dropped = 2646]
2025-03-22T17:55:08.961Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 0 frames already dropped
2025-03-22T17:55:09.962Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 1 frames already dropped
2025-03-22T17:55:10.962Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 2 frames already dropped
2025-03-22T17:55:11.963Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 3 frames already dropped
2025-03-22T17:55:12.963Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 4 frames already dropped
2025-03-22T17:55:13.964Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 5 frames already dropped
2025-03-22T17:55:13.964Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:146) Flush was successful
2025-03-22T17:55:13.964Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:164) Serial port is closed: COM5
2025-03-22T17:55:13.964Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:380) Stopping refresh timer
2025-03-22T17:55:13.964Z [LEDDEVICE0_ADALIGHT] Device 'adalight' is disabled due to an error: 'Timeout writing data to COM5'
2025-03-22T17:55:13.964Z [COMPONENTCTRL0] LED device: disabled
2025-03-22T17:55:13.964Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]
2025-03-22T17:55:16.267Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]
2025-03-22T17:56:16.253Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]
2025-03-22T17:56:25.793Z [WEBSOCKET] (WebSocketClient.cpp:189) send close: 1000 
2025-03-22T17:56:25.873Z [WEBSOCKET] (WebSocketClient.cpp:40) New connection from ::1
2025-03-22T17:56:26.052Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":440}]
2025-03-22T17:56:26.053Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"Serielles USB-Gerät (\\\\.\\COM5)","value":"COM5"}],"ledDeviceType":"adalight"}]
2025-03-22T17:56:34.775Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:285) Stop device
2025-03-22T17:56:34.775Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:296) Disable the device
2025-03-22T17:56:34.775Z [LEDDEVICE0_ADALIGHT]  Stopped LedDevice 'adalight'
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] Start LedDevice 'adalight'.
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:336) deviceConfig: [{"awa_mode":true,"colorOrder":"rgb","currentLedCount":339,"espHandshake":false,"forceSerialDetection":false,"hardwareLedCount":null,"maxRetry":0,"output":"COM5","rate":2000000,"refreshTime":20,"smoothingRefreshTime":20,"type":"adalight","white_channel_calibration":false}]
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] Ignoring user LED refresh rate. Forcing smoothing refresh rate = 50.00 Hz
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:422) Refresh rate = 50.00 Hz
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:372) Device is not ready to start a timer
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:432) Refresh interval updated to 20ms
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:50) DeviceType   : adalight
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:51) LedCount     : 339
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:52) RefreshTime  : 20
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:67) Device name   : COM5
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:68) Auto selection: 0
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:69) Baud rate     : 2000000
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:70) ESP handshake : OFF
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:71) Force ESP/Pico Detection : OFF
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:72) Delayed open  : 0
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:73) Retry limit   : 0
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] The refresh timer is enabled ('Refresh time' > 0) and may limit the performance of the LED driver. Ignore this error if you set it on purpose for some reason (but you almost never need it).
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] (DriverSerialAdalight.cpp:78) Adalight driver with activated high speeed & data integration check AWA protocol
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] (DriverSerialAdalight.cpp:88) Adalight header for 339 leds: Awa 0x01 0x52 0x06
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:246) Enable the device
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] Opening UART: COM5
2025-03-22T17:56:34.776Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:209) _serialPort.open(QIODevice::ReadWrite): COM5, Baud rate [2000000]bps
2025-03-22T17:56:34.777Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:214) portName:          COM5
2025-03-22T17:56:34.777Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:215) systemLocation:    \\.\COM5
2025-03-22T17:56:34.777Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:216) description:       Serielles USB-Ger�t
2025-03-22T17:56:34.777Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:217) manufacturer:      Microsoft
2025-03-22T17:56:34.777Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:218) productIdentifier: 0x80c2
2025-03-22T17:56:34.777Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:219) vendorIdentifier:  0x303a
2025-03-22T17:56:34.777Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:220) serialNumber:      0
2025-03-22T17:56:34.802Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:63) Switch on
2025-03-22T17:56:34.802Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:139) Power On
2025-03-22T17:56:34.802Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:366) Starting timer with interval = 20ms
2025-03-22T17:56:34.802Z [COMPONENTCTRL0] LED device: enabled
2025-03-22T17:56:36.504Z [WEBSOCKET] (WebSocketClient.cpp:189) send close: 1000 
2025-03-22T17:56:36.586Z [WEBSOCKET] (WebSocketClient.cpp:40) New connection from ::1
2025-03-22T17:56:36.747Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":491}]
2025-03-22T17:56:36.748Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"Serielles USB-Gerät (\\\\.\\COM5)","value":"COM5"}],"ledDeviceType":"adalight"}]
2025-03-22T17:56:46.045Z [WEBSOCKET] (WebSocketClient.cpp:189) send close: 1000 
2025-03-22T17:56:46.124Z [WEBSOCKET] (WebSocketClient.cpp:40) New connection from ::1
2025-03-22T17:56:46.281Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":310}]
2025-03-22T17:56:46.282Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"Serielles USB-Gerät (\\\\.\\COM5)","value":"COM5"}],"ledDeviceType":"adalight"}]
2025-03-22T17:56:54.314Z [WEBSOCKET] (HyperAPI.cpp:946) log streaming activated for client ::1
2025-03-22T17:57:32.303Z [WEBSOCKET] (HyperAPI.cpp:955) log streaming deactivated for client  ::1
2025-03-22T17:57:32.374Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":898}]
2025-03-22T17:57:32.376Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"Serielles USB-Gerät (\\\\.\\COM5)","value":"COM5"}],"ledDeviceType":"adalight"}]
2025-03-22T17:57:46.267Z [NET_DISCOVERY] Removing not responding HyperHDR at 192.168.178.24:8090 (LGwebOSTV.local)
2025-03-22T17:58:16.330Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1805, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.09, processed = 1806], [LED0: FPS = 5.88, send = 353, processed = 353, dropped = 2646]
2025-03-22T17:58:28.340Z [NET_DISCOVERY] Found HyperHDR at 192.168.178.24:8090 (LGwebOSTV.local)
2025-03-22T17:58:37.589Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":667}]
2025-03-22T17:58:37.590Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"Serielles USB-Gerät (\\\\.\\COM5)","value":"COM5"}],"ledDeviceType":"adalight"}]
2025-03-22T17:58:43.113Z [WEBSOCKET] (WebSocketClient.cpp:189) send close: 1000 
2025-03-22T17:58:43.228Z [WEBSOCKET] (WebSocketClient.cpp:40) New connection from ::1
2025-03-22T17:58:52.560Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 0 frames already dropped
2025-03-22T17:58:53.560Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 1 frames already dropped
2025-03-22T17:58:54.560Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 2 frames already dropped
2025-03-22T17:58:55.561Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 3 frames already dropped
2025-03-22T17:58:56.561Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 4 frames already dropped
2025-03-22T17:58:57.562Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 5 frames already dropped
2025-03-22T17:58:57.562Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:146) Flush was successful
2025-03-22T17:58:57.562Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:164) Serial port is closed: COM5
2025-03-22T17:58:57.562Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:380) Stopping refresh timer
2025-03-22T17:58:57.562Z [LEDDEVICE0_ADALIGHT] Device 'adalight' is disabled due to an error: 'Timeout writing data to COM5'
2025-03-22T17:58:57.562Z [COMPONENTCTRL0] LED device: disabled
2025-03-22T17:58:57.562Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1805, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.09, processed = 1806]
2025-03-22T17:58:59.571Z [WEBSOCKET] (WebSocketClient.cpp:189) send close: 1000 
2025-03-22T17:58:59.652Z [WEBSOCKET] (WebSocketClient.cpp:40) New connection from ::1
2025-03-22T17:59:16.271Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.08, processed = 1804]
2025-03-22T18:00:16.259Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1805]
2025-03-22T18:01:16.261Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]
2025-03-22T18:02:13.210Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":860}]
2025-03-22T18:02:13.211Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"Serielles USB-Gerät (\\\\.\\COM5)","value":"COM5"}],"ledDeviceType":"adalight"}]
2025-03-22T18:02:16.245Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]
2025-03-22T18:02:16.523Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":665}]
2025-03-22T18:02:16.525Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"Serielles USB-Gerät (\\\\.\\COM5)","value":"COM5"}],"ledDeviceType":"adalight"}]
2025-03-22T18:02:26.674Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:285) Stop device
2025-03-22T18:02:26.674Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:296) Disable the device
2025-03-22T18:02:26.674Z [LEDDEVICE0_ADALIGHT]  Stopped LedDevice 'adalight'
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] Start LedDevice 'adalight'.
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:336) deviceConfig: [{"awa_mode":true,"colorOrder":"rgb","currentLedCount":339,"espHandshake":true,"forceSerialDetection":false,"hardwareLedCount":null,"maxRetry":0,"output":"COM5","rate":2000000,"refreshTime":20,"smoothingRefreshTime":20,"type":"adalight","white_channel_calibration":false}]
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] Ignoring user LED refresh rate. Forcing smoothing refresh rate = 50.00 Hz
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:422) Refresh rate = 50.00 Hz
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:372) Device is not ready to start a timer
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:432) Refresh interval updated to 20ms
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:50) DeviceType   : adalight
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:51) LedCount     : 339
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:52) RefreshTime  : 20
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:67) Device name   : COM5
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:68) Auto selection: 0
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:69) Baud rate     : 2000000
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:70) ESP handshake : ON
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:71) Force ESP/Pico Detection : OFF
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:72) Delayed open  : 0
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:73) Retry limit   : 0
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] The refresh timer is enabled ('Refresh time' > 0) and may limit the performance of the LED driver. Ignore this error if you set it on purpose for some reason (but you almost never need it).
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] (DriverSerialAdalight.cpp:78) Adalight driver with activated high speeed & data integration check AWA protocol
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] (DriverSerialAdalight.cpp:88) Adalight header for 339 leds: Awa 0x01 0x52 0x06
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:246) Enable the device
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] Opening UART: COM5
2025-03-22T18:02:26.675Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:209) _serialPort.open(QIODevice::ReadWrite): COM5, Baud rate [2000000]bps
2025-03-22T18:02:26.676Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:214) portName:          COM5
2025-03-22T18:02:26.676Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:215) systemLocation:    \\.\COM5
2025-03-22T18:02:26.676Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:216) description:       Serielles USB-Ger�t
2025-03-22T18:02:26.676Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:217) manufacturer:      Microsoft
2025-03-22T18:02:26.676Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:218) productIdentifier: 0x80c2
2025-03-22T18:02:26.676Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:219) vendorIdentifier:  0x303a
2025-03-22T18:02:26.676Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:220) serialNumber:      0
2025-03-22T18:02:26.701Z [LEDDEVICE0_ADALIGHT] Detected ESP32-S2 lolin mini type board. HyperHDR skips the reset. State: 0, 0
2025-03-22T18:02:26.782Z [LEDDEVICE0_ADALIGHT] ESP sent: 'HyperHDR frames: 0 (FPS), receiv.: 0, good: 0, incompl.: 0, mem1: 4532, mem2: 3768, heap: 189708'
2025-03-22T18:02:26.782Z [LEDDEVICE0_ADALIGHT] ESP sent: 'RGBW => Gain: 255/255, red: 160, green: 160, blue: 160'
2025-03-22T18:02:26.783Z [LEDDEVICE0_ADALIGHT] DETECTED DEVICE USING HyperSerialEsp8266/HyperSerialESP32/HyperSerialPico FIRMWARE (Welcome! Awa driver 9.) at 2 msec
2025-03-22T18:02:26.783Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:63) Switch on
2025-03-22T18:02:26.783Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:139) Power On
2025-03-22T18:02:26.783Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:366) Starting timer with interval = 20ms
2025-03-22T18:02:26.783Z [COMPONENTCTRL0] LED device: enabled
2025-03-22T18:02:30.685Z [WEBSOCKET] (WebSocketClient.cpp:189) send close: 1000 
2025-03-22T18:02:30.776Z [WEBSOCKET] (WebSocketClient.cpp:40) New connection from ::1
2025-03-22T18:02:30.971Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":873}]
2025-03-22T18:02:30.972Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"Serielles USB-Gerät (\\\\.\\COM5)","value":"COM5"}],"ledDeviceType":"adalight"}]
2025-03-22T18:02:56.324Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:146) Flush was successful
2025-03-22T18:02:56.826Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:164) Serial port is closed: COM5
2025-03-22T18:02:56.826Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:380) Stopping refresh timer
2025-03-22T18:02:56.826Z [LEDDEVICE0_ADALIGHT] Device 'adalight' is disabled due to an error: 'Rs232 SerialPortError: Das Ger�t erkennt den Befehl nicht.'
2025-03-22T18:02:56.826Z [COMPONENTCTRL0] LED device: disabled
2025-03-22T18:03:16.248Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.10, processed = 1806]
2025-03-22T18:04:15.281Z [WEBSOCKET] (WebSocketClient.cpp:189) send close: 1000 
2025-03-22T18:04:15.446Z [WEBSOCKET] (WebSocketClient.cpp:40) New connection from ::1
2025-03-22T18:04:15.784Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":690}]
2025-03-22T18:04:15.786Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"Auto","value":"auto"}],"ledDeviceType":"adalight"}]
2025-03-22T18:04:16.265Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1805, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1805]
2025-03-22T18:04:23.237Z [WEBSOCKET] (HyperAPI.cpp:946) log streaming activated for client ::1
2025-03-22T18:05:16.266Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 2ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]

awawa-dev · 2025-03-22T18:06:06Z

awawa-dev
Mar 22, 2025
Maintainer

Error: ESP32-S2FNR2 (revision v0.0) chip was placed into download mode using GPIO0.
esptool.py can not exit the download mode over USB. To run the app, reset the chip manually.

build_flags = -DNEOPIXEL_RGBW -DCOLD_WHITE -DDATA_PIN=16 -DSECOND_SEGMENT_DATA_PIN=18 -DSECOND_SEGMENT_START_INDEX=169 -DSECOND_SEGMENT_REVERSED ${env.build_flags}

2025-03-22T17:29:16.305Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:51) LedCount : 339

did you reset i? also in HyperHDR you must have exactly 169*2=338 not 339 leds

0 replies

lchmagKekse · 2025-03-22T18:19:00Z

lchmagKekse
Mar 22, 2025
Author

yes ive reset it. the first segment is 169 leds and the second 170. do the segment have to be the exact same length? when configuring 338 leds in HyperHDR i still get the same error.

0 replies

awawa-dev · 2025-03-22T18:20:47Z

awawa-dev
Mar 22, 2025
Maintainer

do the segment have to be the exact same length?

yes, otherwise you can hang the esp

0 replies

awawa-dev · 2025-03-22T18:21:40Z

awawa-dev
Mar 22, 2025
Maintainer

after changing to 338 reset the esp and upload new logs

0 replies

lchmagKekse · 2025-03-22T18:30:04Z

lchmagKekse
Mar 22, 2025
Author

2025-03-22T19:23:41.845Z [MAIN] TTY is not attached to the log output
2025-03-22T19:23:41.845Z [MAIN] Database path: 'C:/Users/alexb/.hyperhdr/db/hyperhdr.db', readonlyMode = disabled
2025-03-22T19:23:41.845Z [MAIN] Starting HyperHdr - 21.0.0.0, (HEAD detached at v21.0.0.0) (Awawa-24e1675/803162c-1741515688), built: Mar  9 2025:10:37:23
2025-03-22T19:23:41.845Z [MAIN] Set user data path to 'C:/Users/alexb/.hyperhdr'
2025-03-22T19:23:41.845Z [INSTANCE_CFG] Loading instance configuration
2025-03-22T19:23:41.846Z [DB] Database opened: C:/Users/alexb/.hyperhdr/db/hyperhdr.db
2025-03-22T19:23:41.858Z [INSTANCE_CFG] Settings database initialized
2025-03-22T19:23:41.863Z [SOUND_GRABBER] Sound device is disabled
2025-03-22T19:23:41.881Z [JSONSERVER] (JsonServer.cpp:26) Created new instance
2025-03-22T19:23:41.890Z [JSONSERVER] Started on port 19444
2025-03-22T19:23:41.891Z [SSDP] (SSDPHandler.cpp:31) SSDPHandler is initialized
2025-03-22T19:23:41.876Z [Media Foundation:auto] (GrabberWrapper.cpp:53) Starting the grabber wrapper
2025-03-22T19:23:41.877Z [MEDIA_FOUNDATION:AUTO] Starting to enumerate video capture devices
2025-03-22T19:23:41.878Z [HYPERHDR0] Starting the instance
2025-03-22T19:23:41.878Z [INSTANCE_CFG0] Loading instance configuration
2025-03-22T19:23:41.878Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:426) Detected 1 devices
2025-03-22T19:23:41.878Z [MEDIA_FOUNDATION:AUTO] Found capture device: Chicony USB2.0 Camera
2025-03-22T19:23:41.879Z [DB] Database opened: C:/Users/alexb/.hyperhdr/db/hyperhdr.db
2025-03-22T19:23:41.888Z [DX11_SYSTEM:\\.\DISPLAY1|A] Restarting video grabber is now blocked due to reloading of the configuration
2025-03-22T19:23:41.888Z [DX11_SYSTEM:\\.\DISPLAY1|A] (Grabber.cpp:276) Set new width: 512, height: 512 for capture
2025-03-22T19:23:41.888Z [DX11_SYSTEM:\\.\DISPLAY1|A] (Grabber.cpp:452) setWidthHeight preparing to restarting video grabber 0
2025-03-22T19:23:41.888Z [DX11_SYSTEM:\\.\DISPLAY1|A] Delayed restart of the grabber due to change of the capturing resolution
2025-03-22T19:23:41.888Z [DX11_SYSTEM:\\.\DISPLAY1|A] Delayed restart of the grabber due to change of the framerate
2025-03-22T19:23:41.888Z [DX11_SYSTEM:\\.\DISPLAY1|A] (DxGrabber.cpp:102) setHdrToneMappingMode to: Disabled
2025-03-22T19:23:41.888Z [DX11_SYSTEM:\\.\DISPLAY1|A] (Grabber.cpp:238) Set hardware acceleration to enabled
2025-03-22T19:23:41.888Z [DX11_SYSTEM:\\.\DISPLAY1|A] Delayed restart of the grabber due to change of the hardware acceleration
2025-03-22T19:23:41.888Z [SIGNAL_OLD] (DetectionManual.cpp:84) Signal detection area set to: 0.250000,0.250000 x 0.750000,0.750000
2025-03-22T19:23:41.888Z [SIGNAL_OLD] (DetectionManual.cpp:74) Signal threshold set to: {0, 0, 0} and frames: 50
2025-03-22T19:23:41.888Z [DX11_SYSTEM:\\.\DISPLAY1|A] (Grabber.cpp:497) setDeviceVideoStandard preparing to restart video grabber. Old: '' new: '\\.\DISPLAY1|AMD Radeon(TM) Graphics'
2025-03-22T19:23:41.888Z [DX11_SYSTEM:\\.\DISPLAY1|A] Delayed restart of the grabber due to change of selected device
2025-03-22T19:23:41.904Z [INSTANCE_CFG0] Settings database initialized
2025-03-22T19:23:41.904Z [COMPONENTCTRL0] (ComponentController.cpp:27) ComponentController is initialized. Components are ENABLED
2025-03-22T19:23:41.905Z [MUXER0] (Muxer.cpp:54) Muxer initialized
2025-03-22T19:23:41.905Z [BLACKBORDER] Set mode to: default
2025-03-22T19:23:41.905Z [IMAGETOLED_MNG0] (ImageToLedManager.cpp:192) Set LED mapping type to advanced
2025-03-22T19:23:41.905Z [IMAGETOLED_MNG0] (ImageToLedManager.cpp:176) setSparseProcessing to 0
2025-03-22T19:23:41.905Z [IMAGETOLED_MNG0] (ImageToLedManager.cpp:103) ImageToLedManager initialized
2025-03-22T19:23:41.905Z [COLORSPACE_CALIBRATION0] classicMode: no, gammas:[1.50, 1.50, 1.50], saturation: 1.00, luminance: 1.00, backLight: [enabled, threshold: 1, colored: yes]
2025-03-22T19:23:41.905Z [LED_CALIBRATION0] (LedCalibration.cpp:101) Calibration config '0' for LED segment: [0, 337]
2025-03-22T19:23:41.906Z [HYPERHDR0] Led strip RGB order is: rgb
2025-03-22T19:23:41.907Z [SMOOTHING0] High resolution clock is steady (good)
2025-03-22T19:23:41.907Z [SMOOTHING0] Clearing queued colors before: enabling
2025-03-22T19:23:41.907Z [SMOOTHING0] Smoothing queue is cleared
2025-03-22T19:23:41.907Z [COMPONENTCTRL0] Smoothing: enabled
2025-03-22T19:23:41.907Z [SMOOTHING0] Creating config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
2025-03-22T19:23:41.907Z [SMOOTHING0] Clearing queued colors before: enabling. Smoothing configuration changed: restarting timer.
2025-03-22T19:23:41.907Z [SMOOTHING0] Smoothing queue is cleared
2025-03-22T19:23:41.907Z [SMOOTHING0] Selecting config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
2025-03-22T19:23:41.907Z [SMOOTHING0] Selecting config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
2025-03-22T19:23:41.908Z [HYPER_MANAGER] HyperHDR instance 'First LED instance' has been started
2025-03-22T19:23:41.907Z [HYPERHDR0] The instance is running
2025-03-22T19:23:41.907Z [MUXER0] Register new input 'System/VIDEOGRABBER' with priority 240 as inactive
2025-03-22T19:23:41.907Z [COMPONENTCTRL0] Video capture device: enabled
2025-03-22T19:23:41.907Z [LEDDEVICE0_ADALIGHT] Start LedDevice 'adalight'.
2025-03-22T19:23:41.907Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:336) deviceConfig: [{"awa_mode":true,"colorOrder":"rgb","currentLedCount":338,"espHandshake":true,"forceSerialDetection":false,"maxRetry":0,"output":"COM5","rate":2000000,"refreshTime":20,"smoothingRefreshTime":20,"type":"adalight","white_channel_calibration":false}]
2025-03-22T19:23:41.907Z [LEDDEVICE0_ADALIGHT] Ignoring user LED refresh rate. Forcing smoothing refresh rate = 50.00 Hz
2025-03-22T19:23:41.908Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:422) Refresh rate = 50.00 Hz
2025-03-22T19:23:41.908Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:372) Device is not ready to start a timer
2025-03-22T19:23:41.908Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:432) Refresh interval updated to 20ms
2025-03-22T19:23:41.908Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:50) DeviceType   : adalight
2025-03-22T19:23:41.908Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:51) LedCount     : 338
2025-03-22T19:23:41.908Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:52) RefreshTime  : 20
2025-03-22T19:23:41.908Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:67) Device name   : COM5
2025-03-22T19:23:41.908Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:68) Auto selection: 0
2025-03-22T19:23:41.908Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:69) Baud rate     : 2000000
2025-03-22T19:23:41.908Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:70) ESP handshake : ON
2025-03-22T19:23:41.908Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:71) Force ESP/Pico Detection : OFF
2025-03-22T19:23:41.908Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:72) Delayed open  : 0
2025-03-22T19:23:41.908Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:73) Retry limit   : 0
2025-03-22T19:23:41.908Z [LEDDEVICE0_ADALIGHT] The refresh timer is enabled ('Refresh time' > 0) and may limit the performance of the LED driver. Ignore this error if you set it on purpose for some reason (but you almost never need it).
2025-03-22T19:23:41.908Z [LEDDEVICE0_ADALIGHT] (DriverSerialAdalight.cpp:78) Adalight driver with activated high speeed & data integration check AWA protocol
2025-03-22T19:23:41.908Z [LEDDEVICE0_ADALIGHT] (DriverSerialAdalight.cpp:88) Adalight header for 338 leds: Awa 0x01 0x51 0x05
2025-03-22T19:23:41.908Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:246) Enable the device
2025-03-22T19:23:41.908Z [LEDDEVICE0_ADALIGHT] Opening UART: COM5
2025-03-22T19:23:41.908Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:209) _serialPort.open(QIODevice::ReadWrite): COM5, Baud rate [2000000]bps
2025-03-22T19:23:41.909Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:214) portName:          COM5
2025-03-22T19:23:41.909Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:215) systemLocation:    \\.\COM5
2025-03-22T19:23:41.909Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:216) description:       Serielles USB-Ger�t
2025-03-22T19:23:41.909Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:217) manufacturer:      Microsoft
2025-03-22T19:23:41.909Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:218) productIdentifier: 0x80c2
2025-03-22T19:23:41.909Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:219) vendorIdentifier:  0x303a
2025-03-22T19:23:41.909Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:220) serialNumber:      0
2025-03-22T19:23:41.935Z [LEDDEVICE0_ADALIGHT] Detected ESP32-S2 lolin mini type board. HyperHDR skips the reset. State: 0, 0
2025-03-22T19:23:41.961Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:465) Device has 'brightness' control => min: 0, max: 100, default: 50
2025-03-22T19:23:41.962Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:472) Device has 'contrast' control => min: 0, max: 100, default: 32
2025-03-22T19:23:41.962Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:479) Device has 'saturation' control => min: 0, max: 20, default: 4
2025-03-22T19:23:41.963Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:486) Device has 'hue' control => min: -180, max: 180, default: 0
2025-03-22T19:23:41.963Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 1280 x 720 @ 30 fps NV12 (nv12)
2025-03-22T19:23:41.963Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 1280 x 720 @ 30 fps MJPG (mjpeg)
2025-03-22T19:23:41.963Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 640 x 480 @ 30 fps NV12 (nv12)
2025-03-22T19:23:41.963Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 640 x 480 @ 30 fps MJPG (mjpeg)
2025-03-22T19:23:41.963Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 640 x 360 @ 30 fps NV12 (nv12)
2025-03-22T19:23:41.963Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 640 x 360 @ 30 fps MJPG (mjpeg)
2025-03-22T19:23:41.963Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 352 x 288 @ 30 fps NV12 (nv12)
2025-03-22T19:23:41.963Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 352 x 288 @ 30 fps MJPG (mjpeg)
2025-03-22T19:23:41.963Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 320 x 240 @ 30 fps NV12 (nv12)
2025-03-22T19:23:41.963Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 320 x 240 @ 30 fps MJPG (mjpeg)
2025-03-22T19:23:41.963Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 176 x 144 @ 30 fps NV12 (nv12)
2025-03-22T19:23:41.963Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 176 x 144 @ 30 fps MJPG (mjpeg)
2025-03-22T19:23:41.963Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 160 x 120 @ 30 fps NV12 (nv12)
2025-03-22T19:23:41.963Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 160 x 120 @ 30 fps MJPG (mjpeg)
2025-03-22T19:23:41.963Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 1280 x 720 @ 10 fps YUY2 (yuyv)
2025-03-22T19:23:41.963Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 640 x 480 @ 30 fps YUY2 (yuyv)
2025-03-22T19:23:41.963Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 640 x 360 @ 30 fps YUY2 (yuyv)
2025-03-22T19:23:41.963Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 352 x 288 @ 30 fps YUY2 (yuyv)
2025-03-22T19:23:41.963Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 320 x 240 @ 30 fps YUY2 (yuyv)
2025-03-22T19:23:41.964Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 176 x 144 @ 30 fps YUY2 (yuyv)
2025-03-22T19:23:41.964Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 160 x 120 @ 30 fps YUY2 (yuyv)
2025-03-22T19:23:41.965Z [MEDIA_FOUNDATION:AUTO] Restarting video grabber is now blocked due to reloading of the configuration
2025-03-22T19:23:41.965Z [MEDIA_FOUNDATION:AUTO] Cropping image: width=0 height=0; crop: left=0 right=0 top=0 bottom=0 
2025-03-22T19:23:41.965Z [Media Foundation:auto] (GrabberWrapper.cpp:180) CEC keycode. Start: 0, stop: 0
2025-03-22T19:23:41.965Z [MEDIA_FOUNDATION:AUTO] (Grabber.cpp:390) setBrightnessContrastSaturationHue nothing changed
2025-03-22T19:23:41.965Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:184) setHdrToneMappingMode to: Disabled
2025-03-22T19:23:41.965Z [AUTOTONEMAPPING] Tone mapping is currently: disabled
2025-03-22T19:23:41.965Z [MEDIA_FOUNDATION:AUTO] (Grabber.cpp:299) setFpsSoftwareDecimation to: 1
2025-03-22T19:23:41.965Z [SIGNAL_OLD] (DetectionManual.cpp:84) Signal detection area set to: 0.250000,0.250000 x 0.750000,0.750000
2025-03-22T19:23:41.965Z [SIGNAL_OLD] (DetectionManual.cpp:74) Signal threshold set to: {12, 12, 12} and frames: 200
2025-03-22T19:23:41.965Z [SIGNAL_AUTO] (DetectionAutomatic.cpp:376) Automatic signal detection -> errorTolerance: 9, modelTolerance: 90, sleepTime: 5000, wakeTime: 1000
2025-03-22T19:23:41.965Z [MEDIA_FOUNDATION:AUTO] (Grabber.cpp:497) setDeviceVideoStandard preparing to restart video grabber. Old: '' new: 'auto'
2025-03-22T19:23:41.965Z [MEDIA_FOUNDATION:AUTO] Delayed restart of the grabber due to change of selected device
2025-03-22T19:23:41.965Z [MEDIA_FOUNDATION:AUTO] (Grabber.cpp:317) Force encoding to: NO_CHANGE (old: NO_CHANGE)
2025-03-22T19:23:41.965Z [MEDIA_FOUNDATION:AUTO] setQFrameDecimation is now: disabled
2025-03-22T19:23:41.965Z [AUTOTONEMAPPING] Enabled: no, time to enable: 30s, time to disable: 500ms, thresholds: { 180, 175, 160}
2025-03-22T19:23:41.965Z [MEDIA_FOUNDATION:AUTO] Multithreading for MEDIA_FOUNDATION is enabled. Available thread's count 4
2025-03-22T19:23:41.965Z [MEDIA_FOUNDATION:AUTO] Starting to enumerate video capture devices
2025-03-22T19:23:41.966Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:426) Detected 1 devices
2025-03-22T19:23:41.966Z [MEDIA_FOUNDATION:AUTO] Found capture device: Chicony USB2.0 Camera
2025-03-22T19:23:41.966Z [FLATBUFSERVER] Tone mapping: 0
2025-03-22T19:23:41.966Z [WEBSERVER] Initialize Webserver
2025-03-22T19:23:41.967Z [FLATBUFSERVER] Started on port 19400
2025-03-22T19:23:41.967Z [FLATBUFSERVER] Started local domain socket server: 'hyperhdr-domain'
2025-03-22T19:23:41.967Z [FLATBUFSERVER] Tone mapping: 0
2025-03-22T19:23:41.967Z [FLATBUFSERVER] NV12 quarter of frame mode: 0
2025-03-22T19:23:41.974Z [NETFORWARDER] Forwarder has changed state to disabled
2025-03-22T19:23:41.982Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:465) Device has 'brightness' control => min: 0, max: 100, default: 50
2025-03-22T19:23:41.983Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:472) Device has 'contrast' control => min: 0, max: 100, default: 32
2025-03-22T19:23:41.983Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:479) Device has 'saturation' control => min: 0, max: 20, default: 4
2025-03-22T19:23:41.983Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:486) Device has 'hue' control => min: -180, max: 180, default: 0
2025-03-22T19:23:41.985Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:261) Forcing auto discovery device
2025-03-22T19:23:41.985Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:266) Auto discovery set to Chicony USB2.0 Camera
2025-03-22T19:23:41.985Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:282) Searching for Chicony USB2.0 Camera 0 x 0 @ 0 fps (NO_CHANGE)
2025-03-22T19:23:41.985Z [MEDIA_FOUNDATION:AUTO] Forcing best guess
2025-03-22T19:23:41.985Z [MEDIA_FOUNDATION:AUTO] *************************************************************************************************
2025-03-22T19:23:41.985Z [MEDIA_FOUNDATION:AUTO] Starting MF grabber. Selected: 'Chicony USB2.0 Camera' 640 x 480 @ 30 fps yuyv
2025-03-22T19:23:41.985Z [MEDIA_FOUNDATION:AUTO] *************************************************************************************************
2025-03-22T19:23:41.985Z [MEDIA_FOUNDATION:AUTO] Init Chicony USB2.0 Camera, 640 x 480 @ 30 fps (YUY2) => \\?\usb#vid_04f2&pid_b729&mi_00#7&191d7230&0&0000#{e5323777-f976-4f5b-9b55-b94699c46e44}\global
2025-03-22T19:23:41.999Z [MEDIA_FOUNDATION:AUTO] Device opened successfully
2025-03-22T19:23:41.999Z [MEDIA_FOUNDATION:AUTO] Brightness set to: 50 (default)
2025-03-22T19:23:41.999Z [MEDIA_FOUNDATION:AUTO] Contrast set to: 32 (default)
2025-03-22T19:23:42.000Z [MEDIA_FOUNDATION:AUTO] Saturation set to: 4 (default)
2025-03-22T19:23:42.000Z [MEDIA_FOUNDATION:AUTO] Hue set to: 0 (default)
2025-03-22T19:23:42.001Z [MEDIA_FOUNDATION:AUTO] ******************** SUCCESFULLY SET CAPTURE PARAMETERS: 640 480 yuyv ********************
2025-03-22T19:23:42.007Z [MEDIA_FOUNDATION:AUTO] (LutLoader.cpp:73) LUT file found: C:/Users/alexb/.hyperhdr/lut_lin_tables.3d (uncompressed)
2025-03-22T19:23:42.007Z [MEDIA_FOUNDATION:AUTO] (LutLoader.cpp:89) Index 2 for YUV
2025-03-22T19:23:42.016Z [LEDDEVICE0_ADALIGHT] ESP sent: 'HyperHDR frames: 0 (FPS), receiv.: 0, good: 0, incompl.: 0, mem1: 4736, mem2: 3768, heap: 189708'
2025-03-22T19:23:42.016Z [LEDDEVICE0_ADALIGHT] ESP sent: 'RGBW => Gain: 255/255, red: 160, green: 160, blue: 160'
2025-03-22T19:23:42.016Z [LEDDEVICE0_ADALIGHT] DETECTED DEVICE USING HyperSerialEsp8266/HyperSerialESP32/HyperSerialPico FIRMWARE (Welcome! Awa driver 9.) at 2 msec
2025-03-22T19:23:42.016Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:63) Switch on
2025-03-22T19:23:42.016Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:139) Power On
2025-03-22T19:23:42.016Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:366) Starting timer with interval = 20ms
2025-03-22T19:23:42.016Z [COMPONENTCTRL0] LED device: enabled
2025-03-22T19:23:42.017Z [SMOOTHING0] Using alternative smoothing input (0)
2025-03-22T19:23:42.017Z [EFFECTENGINE0] Run effect "Rainbow swirl fast" on channel 0
2025-03-22T19:23:42.017Z [EFFECTENGINE0] (EffectEngine.cpp:92) Start the effect: name [Rainbow swirl fast]
2025-03-22T19:23:42.017Z [MUXER0] Register new input 'System/EFFECT' with priority 0 as inactive
2025-03-22T19:23:42.017Z [HYPERHDR0] Boot effect: animation set to 'Rainbow swirl fast' [started]
2025-03-22T19:23:42.017Z [MEDIA_FOUNDATION:AUTO] Found and loaded LUT: 'C:/Users/alexb/.hyperhdr/lut_lin_tables.3d'
2025-03-22T19:23:42.017Z [MEDIA_FOUNDATION:AUTO] Started
2025-03-22T19:23:42.150Z [MUXER0] Set visible priority to 255
2025-03-22T19:23:42.150Z [HYPERHDR0] New priority[255], previous [255]
2025-03-22T19:23:42.150Z [HYPERHDR0] No source left -> switch LED-Device off
2025-03-22T19:23:42.150Z [SMOOTHING0] Clearing queued colors before: disabling
2025-03-22T19:23:42.150Z [SMOOTHING0] Smoothing queue is cleared
2025-03-22T19:23:42.150Z [EFFECT0(Rainbo...)] Begin playing the effect with priority: 0
2025-03-22T19:23:42.150Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:224) setBackLightEnabled: 0
2025-03-22T19:23:42.150Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:296) Disable the device
2025-03-22T19:23:42.150Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:380) Stopping refresh timer
2025-03-22T19:23:42.150Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:89) Switch off
2025-03-22T19:23:42.150Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:543) Set LED strip to black/power off
2025-03-22T19:23:42.150Z [MUXER0] Priority 0 is now active
2025-03-22T19:23:42.150Z [MUXER0] Set visible priority to 0
2025-03-22T19:23:42.150Z [SMOOTHING0] Clearing queued colors before: enabling. Smoothing configuration changed: restarting timer.
2025-03-22T19:23:42.150Z [SMOOTHING0] Smoothing queue is cleared
2025-03-22T19:23:42.150Z [SMOOTHING0] Selecting config (1) => type: Linear, pause: false, settlingTime: 200ms, interval: 40ms (25Hz), antiFlickTres: 0, antiFlickStep: 0, antiFlickTime: 0
2025-03-22T19:23:42.150Z [SMOOTHING0] Using linear smoothing input (1)
2025-03-22T19:23:42.150Z [HYPERHDR0] New priority[0], previous [255]
2025-03-22T19:23:42.150Z [HYPERHDR0] New source available -> switch LED-Device on
2025-03-22T19:23:42.151Z [SMOOTHING0] Clearing queued colors before: enabling
2025-03-22T19:23:42.151Z [SMOOTHING0] Smoothing queue is cleared
2025-03-22T19:23:42.151Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:224) setBackLightEnabled: 0
2025-03-22T19:23:42.151Z [IMAGETOLED_MNG0] Total index number is: 1352 (memory: 1352). User sparse processing is: disabled, image size: 80 x 45, area number: 338
2025-03-22T19:23:42.151Z [SMOOTHING0] Using linear smoothing input (1)
2025-03-22T19:23:42.152Z [WEBSERVER] Apply Webserver settings
2025-03-22T19:23:42.152Z [WEBSERVER] Set document root to: :/www
2025-03-22T19:23:42.153Z [WEBSERVER] Started: 'HyperHDR WebServer (HTTP)' on port: 8090
2025-03-22T19:23:42.153Z [SSDP] (SSDPHandler.cpp:93) The local address is empty
2025-03-22T19:23:42.153Z [WEBSERVER] Initialize Webserver
2025-03-22T19:23:42.153Z [WEBSERVER] Apply Webserver settings
2025-03-22T19:23:42.153Z [WEBSERVER] Set document root to: :/www
2025-03-22T19:23:42.158Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:146) Flush was successful
2025-03-22T19:23:42.159Z [MEDIA_FOUNDATION:AUTO] Received empty image frame: Warning: receive empty sample
2025-03-22T19:23:42.163Z [WEBSERVER] Setup SSL certificate
2025-03-22T19:23:42.163Z [WEBSERVER] Setup private SSL key
2025-03-22T19:23:42.163Z [WEBSERVER] Started: 'HyperHDR WebServer (HTTPS)' on port: 8092
2025-03-22T19:23:42.163Z [SSDP] (SSDPHandler.cpp:42) SSDPHandler is initializing
2025-03-22T19:23:42.166Z [SSDP] (SSDPHandler.cpp:183) The local address is: 192.168.178.31
2025-03-22T19:23:42.166Z [SSDP] (SSDPServer.cpp:94) Initialize the SSDP server
2025-03-22T19:23:42.166Z [SSDP] Starting the SSDP server
2025-03-22T19:23:42.178Z [LEDDEVICE0_ADALIGHT] Received goodbye: 'HyperHDR frames: 0 (FPS), receiv.: 0, good: 0, incompl.: 0, mem1: 3588, mem2: 3720, heap: 144060
' (98)
2025-03-22T19:23:42.200Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:164) Serial port is closed: COM5
2025-03-22T19:23:42.201Z [LEDDEVICE0_ADALIGHT] Ignoring user LED refresh rate. Forcing smoothing refresh rate = 25.00 Hz
2025-03-22T19:23:42.201Z [COMPONENTCTRL0] LED device: disabled
2025-03-22T19:23:42.201Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:422) Refresh rate = 25.00 Hz
2025-03-22T19:23:42.201Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:372) Device is not ready to start a timer
2025-03-22T19:23:42.201Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:432) Refresh interval updated to 40ms
2025-03-22T19:23:42.201Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:447) LED refresh interval adjustment caused by smoothing configuration change to 40ms (proposed: 40ms)
2025-03-22T19:23:42.201Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:246) Enable the device
2025-03-22T19:23:42.201Z [LEDDEVICE0_ADALIGHT] Opening UART: COM5
2025-03-22T19:23:42.201Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:209) _serialPort.open(QIODevice::ReadWrite): COM5, Baud rate [2000000]bps
2025-03-22T19:23:42.202Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:214) portName:          COM5
2025-03-22T19:23:42.202Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:215) systemLocation:    \\.\COM5
2025-03-22T19:23:42.202Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:216) description:       Serielles USB-Ger�t
2025-03-22T19:23:42.202Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:217) manufacturer:      Microsoft
2025-03-22T19:23:42.202Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:218) productIdentifier: 0x80c2
2025-03-22T19:23:42.202Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:219) vendorIdentifier:  0x303a
2025-03-22T19:23:42.202Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:220) serialNumber:      0
2025-03-22T19:23:42.227Z [LEDDEVICE0_ADALIGHT] Detected ESP32-S2 lolin mini type board. HyperHDR skips the reset. State: 0, 0
2025-03-22T19:23:42.307Z [LEDDEVICE0_ADALIGHT] ESP sent: 'HyperHDR frames: 0 (FPS), receiv.: 0, good: 0, incompl.: 0, mem1: 3588, mem2: 3720, heap: 144060'
2025-03-22T19:23:42.308Z [LEDDEVICE0_ADALIGHT] ESP sent: 'RGBW => Gain: 255/255, red: 160, green: 160, blue: 160'
2025-03-22T19:23:42.308Z [LEDDEVICE0_ADALIGHT] DETECTED DEVICE USING HyperSerialEsp8266/HyperSerialESP32/HyperSerialPico FIRMWARE (Welcome! Awa driver 9.) at 2 msec
2025-03-22T19:23:42.308Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:63) Switch on
2025-03-22T19:23:42.308Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:139) Power On
2025-03-22T19:23:42.308Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:366) Starting timer with interval = 40ms
2025-03-22T19:23:42.308Z [COMPONENTCTRL0] LED device: enabled
2025-03-22T19:23:42.341Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:992) Worker's thread count  = 4
2025-03-22T19:23:42.343Z [MUXER0] Priority 240 is now active
2025-03-22T19:23:42.389Z [SMOOTHING0] Using linear smoothing procedure (1)
2025-03-22T19:23:42.690Z [WEBSERVER] Web server resources initialized: C:/Program Files/HyperHDR/bin/../lib/web_resources.rcc
2025-03-22T19:23:43.040Z [WEBSOCKET] (WebSocketClient.cpp:40) New connection from ::1
2025-03-22T19:23:43.166Z [WEBSOCKET] (HyperAPI.cpp:946) log streaming activated for client ::1
2025-03-22T19:23:43.657Z [NET_DISCOVERY] Found ESP32-S2 at COM5:-1 (Serielles USB-Ger�t)
2025-03-22T19:23:43.656Z [SERVICE_mDNS] Starting the network discovery thread
2025-03-22T19:23:45.154Z [EFFECT0(Rainbo...)] The effect quits with priority: 0
2025-03-22T19:23:45.154Z [MUXER0] Removed source priority 0
2025-03-22T19:23:45.154Z [MUXER0] Set visible priority to 240
2025-03-22T19:23:45.154Z [SMOOTHING0] Clearing queued colors before: enabling. Smoothing configuration changed: restarting timer.
2025-03-22T19:23:45.154Z [SMOOTHING0] Smoothing queue is cleared
2025-03-22T19:23:45.154Z [SMOOTHING0] Selecting config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
2025-03-22T19:23:45.154Z [SMOOTHING0] Using alternative smoothing input (0)
2025-03-22T19:23:45.154Z [HYPERHDR0] New priority[240], previous [0]
2025-03-22T19:23:45.154Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:224) setBackLightEnabled: 1
2025-03-22T19:23:45.154Z [EFFECTENGINE0] Effect 'Rainbow swirl fast' has finished.
2025-03-22T19:23:45.154Z [EFFECT0(Rainbo...)] Effect named: 'Rainbow swirl fast' is deleted
2025-03-22T19:23:45.154Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:380) Stopping refresh timer
2025-03-22T19:23:45.154Z [LEDDEVICE0_ADALIGHT] Ignoring user LED refresh rate. Forcing smoothing refresh rate = 50.00 Hz
2025-03-22T19:23:45.154Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:422) Refresh rate = 50.00 Hz
2025-03-22T19:23:45.154Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:366) Starting timer with interval = 20ms
2025-03-22T19:23:45.154Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:432) Refresh interval updated to 20ms
2025-03-22T19:23:45.154Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:447) LED refresh interval adjustment caused by smoothing configuration change to 20ms (proposed: 20ms)
2025-03-22T19:23:45.156Z [IMAGETOLED_MNG0] Total index number is: 79360 (memory: 79360). User sparse processing is: disabled, image size: 640 x 480, area number: 338
2025-03-22T19:23:45.194Z [SMOOTHING0] Using alternative smoothing procedure (0)
2025-03-22T19:24:25.063Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 0 frames already dropped
2025-03-22T19:24:26.064Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 1 frames already dropped
2025-03-22T19:24:27.064Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 2 frames already dropped
2025-03-22T19:24:28.064Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 3 frames already dropped
2025-03-22T19:24:29.065Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 4 frames already dropped
2025-03-22T19:24:30.066Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:293) Timeout after 1000ms: 5 frames already dropped
2025-03-22T19:24:30.066Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:146) Flush was successful
2025-03-22T19:24:30.668Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:164) Serial port is closed: COM5
2025-03-22T19:24:30.668Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:380) Stopping refresh timer
2025-03-22T19:24:30.668Z [LEDDEVICE0_ADALIGHT] Device 'adalight' is disabled due to an error: 'Timeout writing data to COM5'
2025-03-22T19:24:30.669Z [COMPONENTCTRL0] LED device: disabled
2025-03-22T19:24:56.624Z [NET_DISCOVERY] Found HyperHDR at 192.168.178.24:8090 (LGwebOSTV.local)
2025-03-22T19:25:41.845Z [MEDIA_FOUNDATION:AUTO] Video cache: size: 1, hits: 3593, needed: 1, cleanup: 0, limit: 8
2025-03-22T19:25:41.848Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]
2025-03-22T19:26:41.863Z [PERFORMANCE] [USB: FPS = 27.48, decoding = 1ms, frames = 1649, invalid = 0, mode = direct], [INSTANCE0: FPS = 27.48, processed = 1649]
2025-03-22T19:27:41.849Z [PERFORMANCE] [USB: FPS = 27.99, decoding = 1ms, frames = 1679, invalid = 0, mode = direct], [INSTANCE0: FPS = 27.99, processed = 1679]

0 replies

awawa-dev · 2025-03-22T18:35:10Z

awawa-dev
Mar 22, 2025
Maintainer

lower leds to 50 and test again. esp32-s2 is crashing for some reason but there is a communication

0 replies

lchmagKekse · 2025-03-22T18:47:51Z

lchmagKekse
Mar 22, 2025
Author

2025-03-22T19:40:48.952Z [MAIN] TTY is not attached to the log output
2025-03-22T19:40:48.952Z [MAIN] Database path: 'C:/Users/alexb/.hyperhdr/db/hyperhdr.db', readonlyMode = disabled
2025-03-22T19:40:48.952Z [MAIN] Starting HyperHdr - 21.0.0.0, (HEAD detached at v21.0.0.0) (Awawa-24e1675/803162c-1741515688), built: Mar  9 2025:10:37:23
2025-03-22T19:40:48.952Z [MAIN] Set user data path to 'C:/Users/alexb/.hyperhdr'
2025-03-22T19:40:48.952Z [INSTANCE_CFG] Loading instance configuration
2025-03-22T19:40:48.952Z [DB] Database opened: C:/Users/alexb/.hyperhdr/db/hyperhdr.db
2025-03-22T19:40:48.959Z [INSTANCE_CFG] Settings database initialized
2025-03-22T19:40:48.964Z [SOUND_GRABBER] Sound device is disabled
2025-03-22T19:40:48.981Z [JSONSERVER] (JsonServer.cpp:26) Created new instance
2025-03-22T19:40:48.991Z [JSONSERVER] Started on port 19444
2025-03-22T19:40:48.992Z [SSDP] (SSDPHandler.cpp:31) SSDPHandler is initialized
2025-03-22T19:40:48.978Z [Media Foundation:auto] (GrabberWrapper.cpp:53) Starting the grabber wrapper
2025-03-22T19:40:48.978Z [MEDIA_FOUNDATION:AUTO] Starting to enumerate video capture devices
2025-03-22T19:40:48.979Z [HYPERHDR0] Starting the instance
2025-03-22T19:40:48.979Z [INSTANCE_CFG0] Loading instance configuration
2025-03-22T19:40:48.979Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:426) Detected 1 devices
2025-03-22T19:40:48.979Z [MEDIA_FOUNDATION:AUTO] Found capture device: Chicony USB2.0 Camera
2025-03-22T19:40:48.979Z [DB] Database opened: C:/Users/alexb/.hyperhdr/db/hyperhdr.db
2025-03-22T19:40:48.989Z [DX11_SYSTEM:\\.\DISPLAY1|A] Restarting video grabber is now blocked due to reloading of the configuration
2025-03-22T19:40:48.989Z [DX11_SYSTEM:\\.\DISPLAY1|A] (Grabber.cpp:276) Set new width: 512, height: 512 for capture
2025-03-22T19:40:48.989Z [DX11_SYSTEM:\\.\DISPLAY1|A] (Grabber.cpp:452) setWidthHeight preparing to restarting video grabber 0
2025-03-22T19:40:48.989Z [DX11_SYSTEM:\\.\DISPLAY1|A] Delayed restart of the grabber due to change of the capturing resolution
2025-03-22T19:40:48.989Z [DX11_SYSTEM:\\.\DISPLAY1|A] Delayed restart of the grabber due to change of the framerate
2025-03-22T19:40:48.989Z [DX11_SYSTEM:\\.\DISPLAY1|A] (DxGrabber.cpp:102) setHdrToneMappingMode to: Disabled
2025-03-22T19:40:48.989Z [DX11_SYSTEM:\\.\DISPLAY1|A] (Grabber.cpp:238) Set hardware acceleration to enabled
2025-03-22T19:40:48.989Z [DX11_SYSTEM:\\.\DISPLAY1|A] Delayed restart of the grabber due to change of the hardware acceleration
2025-03-22T19:40:48.989Z [SIGNAL_OLD] (DetectionManual.cpp:84) Signal detection area set to: 0.250000,0.250000 x 0.750000,0.750000
2025-03-22T19:40:48.989Z [SIGNAL_OLD] (DetectionManual.cpp:74) Signal threshold set to: {0, 0, 0} and frames: 50
2025-03-22T19:40:48.989Z [DX11_SYSTEM:\\.\DISPLAY1|A] (Grabber.cpp:497) setDeviceVideoStandard preparing to restart video grabber. Old: '' new: '\\.\DISPLAY1|AMD Radeon(TM) Graphics'
2025-03-22T19:40:48.989Z [DX11_SYSTEM:\\.\DISPLAY1|A] Delayed restart of the grabber due to change of selected device
2025-03-22T19:40:48.993Z [INSTANCE_CFG0] Settings database initialized
2025-03-22T19:40:48.993Z [COMPONENTCTRL0] (ComponentController.cpp:27) ComponentController is initialized. Components are ENABLED
2025-03-22T19:40:48.993Z [MUXER0] (Muxer.cpp:54) Muxer initialized
2025-03-22T19:40:48.993Z [BLACKBORDER] Set mode to: default
2025-03-22T19:40:48.993Z [IMAGETOLED_MNG0] (ImageToLedManager.cpp:192) Set LED mapping type to advanced
2025-03-22T19:40:48.993Z [IMAGETOLED_MNG0] (ImageToLedManager.cpp:176) setSparseProcessing to 0
2025-03-22T19:40:48.993Z [IMAGETOLED_MNG0] (ImageToLedManager.cpp:103) ImageToLedManager initialized
2025-03-22T19:40:48.993Z [COLORSPACE_CALIBRATION0] classicMode: no, gammas:[1.50, 1.50, 1.50], saturation: 1.00, luminance: 1.00, backLight: [enabled, threshold: 1, colored: yes]
2025-03-22T19:40:48.993Z [LED_CALIBRATION0] (LedCalibration.cpp:101) Calibration config '0' for LED segment: [0, 49]
2025-03-22T19:40:48.993Z [HYPERHDR0] Led strip RGB order is: rgb
2025-03-22T19:40:48.994Z [SMOOTHING0] High resolution clock is steady (good)
2025-03-22T19:40:48.994Z [SMOOTHING0] Clearing queued colors before: enabling
2025-03-22T19:40:48.994Z [SMOOTHING0] Smoothing queue is cleared
2025-03-22T19:40:48.994Z [COMPONENTCTRL0] Smoothing: enabled
2025-03-22T19:40:48.994Z [SMOOTHING0] Creating config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
2025-03-22T19:40:48.994Z [SMOOTHING0] Clearing queued colors before: enabling. Smoothing configuration changed: restarting timer.
2025-03-22T19:40:48.994Z [SMOOTHING0] Smoothing queue is cleared
2025-03-22T19:40:48.994Z [SMOOTHING0] Selecting config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
2025-03-22T19:40:48.994Z [SMOOTHING0] Selecting config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
2025-03-22T19:40:49.002Z [HYPER_MANAGER] HyperHDR instance 'First LED instance' has been started
2025-03-22T19:40:48.995Z [HYPERHDR0] The instance is running
2025-03-22T19:40:48.995Z [MUXER0] Register new input 'System/VIDEOGRABBER' with priority 240 as inactive
2025-03-22T19:40:48.995Z [COMPONENTCTRL0] Video capture device: enabled
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] Start LedDevice 'adalight'.
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:336) deviceConfig: [{"awa_mode":true,"colorOrder":"rgb","currentLedCount":50,"espHandshake":true,"forceSerialDetection":false,"maxRetry":0,"output":"COM5","rate":2000000,"refreshTime":20,"smoothingRefreshTime":20,"type":"adalight","white_channel_calibration":false}]
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] Ignoring user LED refresh rate. Forcing smoothing refresh rate = 50.00 Hz
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:422) Refresh rate = 50.00 Hz
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:372) Device is not ready to start a timer
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:432) Refresh interval updated to 20ms
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:50) DeviceType   : adalight
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:51) LedCount     : 50
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:52) RefreshTime  : 20
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:67) Device name   : COM5
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:68) Auto selection: 0
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:69) Baud rate     : 2000000
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:70) ESP handshake : ON
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:71) Force ESP/Pico Detection : OFF
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:72) Delayed open  : 0
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:73) Retry limit   : 0
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] The refresh timer is enabled ('Refresh time' > 0) and may limit the performance of the LED driver. Ignore this error if you set it on purpose for some reason (but you almost never need it).
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] (DriverSerialAdalight.cpp:78) Adalight driver with activated high speeed & data integration check AWA protocol
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] (DriverSerialAdalight.cpp:88) Adalight header for 50 leds: Awa 0x00 0x31 0x64
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:246) Enable the device
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] Opening UART: COM5
2025-03-22T19:40:48.995Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:209) _serialPort.open(QIODevice::ReadWrite): COM5, Baud rate [2000000]bps
2025-03-22T19:40:48.996Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:214) portName:          COM5
2025-03-22T19:40:48.996Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:215) systemLocation:    \\.\COM5
2025-03-22T19:40:48.996Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:216) description:       Serielles USB-Ger�t
2025-03-22T19:40:48.996Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:217) manufacturer:      Microsoft
2025-03-22T19:40:48.996Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:218) productIdentifier: 0x80c2
2025-03-22T19:40:48.996Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:219) vendorIdentifier:  0x303a
2025-03-22T19:40:48.996Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:220) serialNumber:      0
2025-03-22T19:40:49.022Z [LEDDEVICE0_ADALIGHT] Detected ESP32-S2 lolin mini type board. HyperHDR skips the reset. State: 0, 0
2025-03-22T19:40:49.061Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:465) Device has 'brightness' control => min: 0, max: 100, default: 50
2025-03-22T19:40:49.061Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:472) Device has 'contrast' control => min: 0, max: 100, default: 32
2025-03-22T19:40:49.061Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:479) Device has 'saturation' control => min: 0, max: 20, default: 4
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:486) Device has 'hue' control => min: -180, max: 180, default: 0
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 1280 x 720 @ 30 fps NV12 (nv12)
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 1280 x 720 @ 30 fps MJPG (mjpeg)
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 640 x 480 @ 30 fps NV12 (nv12)
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 640 x 480 @ 30 fps MJPG (mjpeg)
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 640 x 360 @ 30 fps NV12 (nv12)
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 640 x 360 @ 30 fps MJPG (mjpeg)
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 352 x 288 @ 30 fps NV12 (nv12)
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 352 x 288 @ 30 fps MJPG (mjpeg)
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 320 x 240 @ 30 fps NV12 (nv12)
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 320 x 240 @ 30 fps MJPG (mjpeg)
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 176 x 144 @ 30 fps NV12 (nv12)
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 176 x 144 @ 30 fps MJPG (mjpeg)
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 160 x 120 @ 30 fps NV12 (nv12)
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 160 x 120 @ 30 fps MJPG (mjpeg)
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 1280 x 720 @ 10 fps YUY2 (yuyv)
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 640 x 480 @ 30 fps YUY2 (yuyv)
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 640 x 360 @ 30 fps YUY2 (yuyv)
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 352 x 288 @ 30 fps YUY2 (yuyv)
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 320 x 240 @ 30 fps YUY2 (yuyv)
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 176 x 144 @ 30 fps YUY2 (yuyv)
2025-03-22T19:40:49.062Z [MEDIA_FOUNDATION:AUTO] Chicony USB2.0 Camera 160 x 120 @ 30 fps YUY2 (yuyv)
2025-03-22T19:40:49.064Z [MEDIA_FOUNDATION:AUTO] Restarting video grabber is now blocked due to reloading of the configuration
2025-03-22T19:40:49.064Z [MEDIA_FOUNDATION:AUTO] Cropping image: width=0 height=0; crop: left=0 right=0 top=0 bottom=0 
2025-03-22T19:40:49.064Z [Media Foundation:auto] (GrabberWrapper.cpp:180) CEC keycode. Start: 0, stop: 0
2025-03-22T19:40:49.064Z [MEDIA_FOUNDATION:AUTO] (Grabber.cpp:390) setBrightnessContrastSaturationHue nothing changed
2025-03-22T19:40:49.064Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:184) setHdrToneMappingMode to: Disabled
2025-03-22T19:40:49.064Z [AUTOTONEMAPPING] Tone mapping is currently: disabled
2025-03-22T19:40:49.064Z [MEDIA_FOUNDATION:AUTO] (Grabber.cpp:299) setFpsSoftwareDecimation to: 1
2025-03-22T19:40:49.064Z [SIGNAL_OLD] (DetectionManual.cpp:84) Signal detection area set to: 0.250000,0.250000 x 0.750000,0.750000
2025-03-22T19:40:49.064Z [SIGNAL_OLD] (DetectionManual.cpp:74) Signal threshold set to: {12, 12, 12} and frames: 200
2025-03-22T19:40:49.064Z [SIGNAL_AUTO] (DetectionAutomatic.cpp:376) Automatic signal detection -> errorTolerance: 9, modelTolerance: 90, sleepTime: 5000, wakeTime: 1000
2025-03-22T19:40:49.064Z [MEDIA_FOUNDATION:AUTO] (Grabber.cpp:497) setDeviceVideoStandard preparing to restart video grabber. Old: '' new: 'auto'
2025-03-22T19:40:49.064Z [MEDIA_FOUNDATION:AUTO] Delayed restart of the grabber due to change of selected device
2025-03-22T19:40:49.064Z [MEDIA_FOUNDATION:AUTO] (Grabber.cpp:317) Force encoding to: NO_CHANGE (old: NO_CHANGE)
2025-03-22T19:40:49.064Z [MEDIA_FOUNDATION:AUTO] setQFrameDecimation is now: disabled
2025-03-22T19:40:49.064Z [AUTOTONEMAPPING] Enabled: no, time to enable: 30s, time to disable: 500ms, thresholds: { 180, 175, 160}
2025-03-22T19:40:49.064Z [MEDIA_FOUNDATION:AUTO] Multithreading for MEDIA_FOUNDATION is enabled. Available thread's count 4
2025-03-22T19:40:49.064Z [MEDIA_FOUNDATION:AUTO] Starting to enumerate video capture devices
2025-03-22T19:40:49.064Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:426) Detected 1 devices
2025-03-22T19:40:49.064Z [MEDIA_FOUNDATION:AUTO] Found capture device: Chicony USB2.0 Camera
2025-03-22T19:40:49.066Z [FLATBUFSERVER] Tone mapping: 0
2025-03-22T19:40:49.066Z [WEBSERVER] Initialize Webserver
2025-03-22T19:40:49.066Z [FLATBUFSERVER] Started on port 19400
2025-03-22T19:40:49.067Z [FLATBUFSERVER] Started local domain socket server: 'hyperhdr-domain'
2025-03-22T19:40:49.067Z [FLATBUFSERVER] Tone mapping: 0
2025-03-22T19:40:49.067Z [FLATBUFSERVER] NV12 quarter of frame mode: 0
2025-03-22T19:40:49.073Z [NETFORWARDER] Forwarder has changed state to disabled
2025-03-22T19:40:49.073Z [WEBSERVER] Apply Webserver settings
2025-03-22T19:40:49.073Z [WEBSERVER] Set document root to: :/www
2025-03-22T19:40:49.074Z [WEBSERVER] Started: 'HyperHDR WebServer (HTTP)' on port: 8090
2025-03-22T19:40:49.074Z [SSDP] (SSDPHandler.cpp:93) The local address is empty
2025-03-22T19:40:49.074Z [WEBSERVER] Initialize Webserver
2025-03-22T19:40:49.074Z [WEBSERVER] Apply Webserver settings
2025-03-22T19:40:49.074Z [WEBSERVER] Set document root to: :/www
2025-03-22T19:40:49.080Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:465) Device has 'brightness' control => min: 0, max: 100, default: 50
2025-03-22T19:40:49.080Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:472) Device has 'contrast' control => min: 0, max: 100, default: 32
2025-03-22T19:40:49.080Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:479) Device has 'saturation' control => min: 0, max: 20, default: 4
2025-03-22T19:40:49.081Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:486) Device has 'hue' control => min: -180, max: 180, default: 0
2025-03-22T19:40:49.083Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:261) Forcing auto discovery device
2025-03-22T19:40:49.083Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:266) Auto discovery set to Chicony USB2.0 Camera
2025-03-22T19:40:49.083Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:282) Searching for Chicony USB2.0 Camera 0 x 0 @ 0 fps (NO_CHANGE)
2025-03-22T19:40:49.083Z [MEDIA_FOUNDATION:AUTO] Forcing best guess
2025-03-22T19:40:49.083Z [MEDIA_FOUNDATION:AUTO] *************************************************************************************************
2025-03-22T19:40:49.083Z [MEDIA_FOUNDATION:AUTO] Starting MF grabber. Selected: 'Chicony USB2.0 Camera' 640 x 480 @ 30 fps yuyv
2025-03-22T19:40:49.083Z [MEDIA_FOUNDATION:AUTO] *************************************************************************************************
2025-03-22T19:40:49.083Z [MEDIA_FOUNDATION:AUTO] Init Chicony USB2.0 Camera, 640 x 480 @ 30 fps (YUY2) => \\?\usb#vid_04f2&pid_b729&mi_00#7&191d7230&0&0000#{e5323777-f976-4f5b-9b55-b94699c46e44}\global
2025-03-22T19:40:49.083Z [WEBSERVER] Setup SSL certificate
2025-03-22T19:40:49.084Z [WEBSERVER] Setup private SSL key
2025-03-22T19:40:49.084Z [WEBSERVER] Started: 'HyperHDR WebServer (HTTPS)' on port: 8092
2025-03-22T19:40:49.084Z [SSDP] (SSDPHandler.cpp:42) SSDPHandler is initializing
2025-03-22T19:40:49.087Z [SSDP] (SSDPHandler.cpp:183) The local address is: 192.168.178.31
2025-03-22T19:40:49.087Z [SSDP] (SSDPServer.cpp:94) Initialize the SSDP server
2025-03-22T19:40:49.087Z [SSDP] Starting the SSDP server
2025-03-22T19:40:49.095Z [MEDIA_FOUNDATION:AUTO] Device opened successfully
2025-03-22T19:40:49.096Z [MEDIA_FOUNDATION:AUTO] Brightness set to: 50 (default)
2025-03-22T19:40:49.097Z [MEDIA_FOUNDATION:AUTO] Contrast set to: 32 (default)
2025-03-22T19:40:49.097Z [MEDIA_FOUNDATION:AUTO] Saturation set to: 4 (default)
2025-03-22T19:40:49.097Z [MEDIA_FOUNDATION:AUTO] Hue set to: 0 (default)
2025-03-22T19:40:49.098Z [MEDIA_FOUNDATION:AUTO] ******************** SUCCESFULLY SET CAPTURE PARAMETERS: 640 480 yuyv ********************
2025-03-22T19:40:49.098Z [MEDIA_FOUNDATION:AUTO] (LutLoader.cpp:73) LUT file found: C:/Users/alexb/.hyperhdr/lut_lin_tables.3d (uncompressed)
2025-03-22T19:40:49.098Z [MEDIA_FOUNDATION:AUTO] (LutLoader.cpp:89) Index 2 for YUV
2025-03-22T19:40:49.103Z [LEDDEVICE0_ADALIGHT] ESP sent: 'HyperHDR frames: 0 (FPS), receiv.: 0, good: 0, incompl.: 0, mem1: 4736, mem2: 3768, heap: 189708'
2025-03-22T19:40:49.104Z [LEDDEVICE0_ADALIGHT] ESP sent: 'RGBW => Gain: 255/255, red: 160, green: 160, blue: 160'
2025-03-22T19:40:49.104Z [LEDDEVICE0_ADALIGHT] DETECTED DEVICE USING HyperSerialEsp8266/HyperSerialESP32/HyperSerialPico FIRMWARE (Welcome! Awa driver 9.) at 2 msec
2025-03-22T19:40:49.104Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:63) Switch on
2025-03-22T19:40:49.104Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:139) Power On
2025-03-22T19:40:49.104Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:366) Starting timer with interval = 20ms
2025-03-22T19:40:49.104Z [COMPONENTCTRL0] LED device: enabled
2025-03-22T19:40:49.104Z [SMOOTHING0] Using alternative smoothing input (0)
2025-03-22T19:40:49.104Z [EFFECTENGINE0] Run effect "Rainbow swirl fast" on channel 0
2025-03-22T19:40:49.104Z [EFFECTENGINE0] (EffectEngine.cpp:92) Start the effect: name [Rainbow swirl fast]
2025-03-22T19:40:49.104Z [MUXER0] Register new input 'System/EFFECT' with priority 0 as inactive
2025-03-22T19:40:49.105Z [HYPERHDR0] Boot effect: animation set to 'Rainbow swirl fast' [started]
2025-03-22T19:40:49.105Z [EFFECT0(Rainbo...)] Begin playing the effect with priority: 0
2025-03-22T19:40:49.105Z [MUXER0] Priority 0 is now active
2025-03-22T19:40:49.105Z [MUXER0] Set visible priority to 0
2025-03-22T19:40:49.105Z [SMOOTHING0] Clearing queued colors before: enabling. Smoothing configuration changed: restarting timer.
2025-03-22T19:40:49.105Z [SMOOTHING0] Smoothing queue is cleared
2025-03-22T19:40:49.105Z [SMOOTHING0] Selecting config (1) => type: Linear, pause: false, settlingTime: 200ms, interval: 40ms (25Hz), antiFlickTres: 0, antiFlickStep: 0, antiFlickTime: 0
2025-03-22T19:40:49.105Z [SMOOTHING0] Using linear smoothing input (1)
2025-03-22T19:40:49.106Z [HYPERHDR0] New priority[0], previous [255]
2025-03-22T19:40:49.106Z [HYPERHDR0] New source available -> switch LED-Device on
2025-03-22T19:40:49.106Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:380) Stopping refresh timer
2025-03-22T19:40:49.106Z [SMOOTHING0] Clearing queued colors before: enabling
2025-03-22T19:40:49.106Z [LEDDEVICE0_ADALIGHT] Ignoring user LED refresh rate. Forcing smoothing refresh rate = 25.00 Hz
2025-03-22T19:40:49.106Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:422) Refresh rate = 25.00 Hz
2025-03-22T19:40:49.106Z [SMOOTHING0] Smoothing queue is cleared
2025-03-22T19:40:49.106Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:366) Starting timer with interval = 40ms
2025-03-22T19:40:49.106Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:432) Refresh interval updated to 40ms
2025-03-22T19:40:49.106Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:447) LED refresh interval adjustment caused by smoothing configuration change to 40ms (proposed: 40ms)
2025-03-22T19:40:49.106Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:224) setBackLightEnabled: 0
2025-03-22T19:40:49.106Z [IMAGETOLED_MNG0] Total index number is: 640 (memory: 640). User sparse processing is: disabled, image size: 80 x 45, area number: 50
2025-03-22T19:40:49.106Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:246) Enable the device
2025-03-22T19:40:49.106Z [SMOOTHING0] Using linear smoothing input (1)
2025-03-22T19:40:49.108Z [MEDIA_FOUNDATION:AUTO] Found and loaded LUT: 'C:/Users/alexb/.hyperhdr/lut_lin_tables.3d'
2025-03-22T19:40:49.108Z [MEDIA_FOUNDATION:AUTO] Started
2025-03-22T19:40:49.117Z [MEDIA_FOUNDATION:AUTO] Received empty image frame: Warning: receive empty sample
2025-03-22T19:40:49.187Z [SMOOTHING0] Using linear smoothing procedure (1)
2025-03-22T19:40:49.251Z [WEBSERVER] Web server resources initialized: C:/Program Files/HyperHDR/bin/../lib/web_resources.rcc
2025-03-22T19:40:49.300Z [MEDIA_FOUNDATION:AUTO] (MFGrabber.cpp:992) Worker's thread count  = 4
2025-03-22T19:40:49.303Z [MUXER0] Priority 240 is now active
2025-03-22T19:40:49.361Z [WEBSOCKET] (WebSocketClient.cpp:40) New connection from ::1
2025-03-22T19:40:49.524Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":271}]
2025-03-22T19:40:49.528Z [NET_DISCOVERY] Found ESP32-S2 at COM5:-1 (Serielles USB-Ger�t)
2025-03-22T19:40:49.524Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"Serielles USB-Gerät (\\\\.\\COM5)","value":"COM5"}],"ledDeviceType":"adalight"}]
2025-03-22T19:40:50.576Z [SERVICE_mDNS] Starting the network discovery thread
2025-03-22T19:40:50.591Z [NET_DISCOVERY] Found HyperHDR at 192.168.178.24:8090 (LGwebOSTV.local)
2025-03-22T19:40:52.108Z [EFFECT0(Rainbo...)] The effect quits with priority: 0
2025-03-22T19:40:52.108Z [MUXER0] Removed source priority 0
2025-03-22T19:40:52.108Z [MUXER0] Set visible priority to 240
2025-03-22T19:40:52.108Z [SMOOTHING0] Clearing queued colors before: enabling. Smoothing configuration changed: restarting timer.
2025-03-22T19:40:52.108Z [SMOOTHING0] Smoothing queue is cleared
2025-03-22T19:40:52.109Z [SMOOTHING0] Selecting config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
2025-03-22T19:40:52.109Z [SMOOTHING0] Using alternative smoothing input (0)
2025-03-22T19:40:52.109Z [HYPERHDR0] New priority[240], previous [0]
2025-03-22T19:40:52.109Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:224) setBackLightEnabled: 1
2025-03-22T19:40:52.109Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:380) Stopping refresh timer
2025-03-22T19:40:52.109Z [LEDDEVICE0_ADALIGHT] Ignoring user LED refresh rate. Forcing smoothing refresh rate = 50.00 Hz
2025-03-22T19:40:52.109Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:422) Refresh rate = 50.00 Hz
2025-03-22T19:40:52.109Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:366) Starting timer with interval = 20ms
2025-03-22T19:40:52.109Z [EFFECTENGINE0] Effect 'Rainbow swirl fast' has finished.
2025-03-22T19:40:52.109Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:432) Refresh interval updated to 20ms
2025-03-22T19:40:52.109Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:447) LED refresh interval adjustment caused by smoothing configuration change to 20ms (proposed: 20ms)
2025-03-22T19:40:52.109Z [EFFECT0(Rainbo...)] Effect named: 'Rainbow swirl fast' is deleted
2025-03-22T19:40:52.113Z [IMAGETOLED_MNG0] Total index number is: 48640 (memory: 48640). User sparse processing is: disabled, image size: 640 x 480, area number: 50
2025-03-22T19:40:52.149Z [SMOOTHING0] Using alternative smoothing procedure (0)
2025-03-22T19:40:52.593Z [WEBSOCKET] (HyperAPI.cpp:946) log streaming activated for client ::1
2025-03-22T19:41:38.229Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:146) Flush was successful
2025-03-22T19:41:38.731Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:164) Serial port is closed: COM5
2025-03-22T19:41:38.731Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:380) Stopping refresh timer
2025-03-22T19:41:38.731Z [LEDDEVICE0_ADALIGHT] Device 'adalight' is disabled due to an error: 'Rs232 SerialPortError: Das Ger�t erkennt den Befehl nicht.'
2025-03-22T19:41:38.731Z [COMPONENTCTRL0] LED device: disabled
2025-03-22T19:42:48.963Z [MEDIA_FOUNDATION:AUTO] Video cache: size: 1, hits: 3598, needed: 1, cleanup: 0, limit: 8
2025-03-22T19:42:48.964Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1805, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1805]
2025-03-22T19:43:48.966Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]
2025-03-22T19:44:42.299Z [WEBSOCKET] (WebSocketClient.cpp:189) send close: 1000 
2025-03-22T19:44:42.393Z [WEBSOCKET] (WebSocketClient.cpp:40) New connection from ::1
2025-03-22T19:44:42.510Z [WEBSOCKET] (HyperAPI.cpp:946) log streaming activated for client ::1
2025-03-22T19:44:48.951Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]
2025-03-22T19:45:48.953Z [PERFORMANCE] [USB: FPS = 30.07, decoding = 1ms, frames = 1804, invalid = 0, mode = direct], [INSTANCE0: FPS = 30.07, processed = 1804]
2025-03-22T19:45:53.297Z [WEBSOCKET] (WebSocketClient.cpp:189) send close: 1000 
2025-03-22T19:45:53.372Z [WEBSOCKET] (WebSocketClient.cpp:40) New connection from ::1
2025-03-22T19:45:53.494Z [WEBSOCKET] (HyperAPI.cpp:946) log streaming activated for client ::1

'Rs232 SerialPortError: Das Ger�t erkennt den Befehl nicht.' translates to The device does not recognize the command.

0 replies

awawa-dev · 2025-03-22T19:31:19Z

awawa-dev
Mar 22, 2025
Maintainer

I cant find your fork of HyperSerialESP32 to verify the build. Did you compile the firmware on your computer? Please follow the standard path to build a firmware then we will see.

0 replies

lchmagKekse · 2025-03-22T20:06:13Z

lchmagKekse
Mar 22, 2025
Author

Using the build from github actions made the error disapear from the logs. Also my level shifter was broken. I replaced it and now it works.

Thank you for your help ❤️

0 replies

awawa-dev · 2025-03-22T20:09:31Z

awawa-dev
Mar 22, 2025
Maintainer

Great! I'm glad you managed to get it up and running 👍

0 replies

Uh oh!

'Timeout writing data to COM5' and 'Rs232 SerialPortError' after erase_flash on ESP32 S2 Mini #85

Uh oh!

lchmagKekse Mar 22, 2025

Replies: 10 comments

Uh oh!

awawa-dev Mar 22, 2025 Maintainer

Uh oh!

lchmagKekse Mar 22, 2025 Author

Uh oh!

awawa-dev Mar 22, 2025 Maintainer

Uh oh!

awawa-dev Mar 22, 2025 Maintainer

Uh oh!

Uh oh!

lchmagKekse Mar 22, 2025 Author

Uh oh!

awawa-dev Mar 22, 2025 Maintainer

Uh oh!

lchmagKekse Mar 22, 2025 Author

Uh oh!

awawa-dev Mar 22, 2025 Maintainer

Uh oh!

lchmagKekse Mar 22, 2025 Author

Uh oh!

awawa-dev Mar 22, 2025 Maintainer

lchmagKekse
Mar 22, 2025

awawa-dev
Mar 22, 2025
Maintainer

lchmagKekse
Mar 22, 2025
Author

awawa-dev
Mar 22, 2025
Maintainer

awawa-dev
Mar 22, 2025
Maintainer

lchmagKekse
Mar 22, 2025
Author

awawa-dev
Mar 22, 2025
Maintainer

lchmagKekse
Mar 22, 2025
Author

awawa-dev
Mar 22, 2025
Maintainer

lchmagKekse
Mar 22, 2025
Author

awawa-dev
Mar 22, 2025
Maintainer